GLD4660NS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Oak Hill, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
4 wheels missing from diswasher rack (lower)
removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- R. Cecil from Norfolk, VA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheel was distorted
Simply replace wheel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Williston, ND
- Parts Used:
- WD22X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes were not cleaning properly
Self
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Fair Oaks Ranch, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom shelf would not roll properly
so easy! Ordered the rollers and clips ... popped them on and done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from mashpee, MA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom basket of dishwasher kept following out
i needed new rollers and inserts to keep wheels on now its like new when i pull out bottom basket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- selleck from kingston, NY
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable), Wrench set
Did not have water flowing into dishwasher
I removed the old valve with wrench and Philips screw driver.Unscrewed the mounting plate and water hose. When I went to replace the new water inlet valve, I found that there was a mismatch on the screw holes for the new mounting plate. Different screw threads. I tried to find screws that would fit, but didn't have any.So I manged to make the old screws re-thread themselves and hold the plate in place. I then attached the water hose and started the dishwasher up. Make sure to power off the unit then power it back on to clear and reset the programming. Works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Chatham, NJ
- Parts Used:
- WD35X21038
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
wheels colapsed
replaced new wheels
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Alexandria, VA
- Parts Used:
- WD35X21038, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost wheel
just snapped the new part in. couldn't have been easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROY from CULPEPER, VA
- Parts Used:
- WD13X10045
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door handle actuator
Parts were easy to find, easy to order and arrived prior to the advertised delivery date. Instructions for replacement were easy to understand and in about 10 minutes the old part was removed, and the new one installed. thanks for your prompt and efficient company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Tinton Falls, NJ
- Parts Used:
- WD22X10029
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The old plastic filter's corner were bent up allow food to get into the plumbing going to the articulation sprayers and clogging them.
Remove bottom articulating sprayer and water fittings. Remove and replace filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from St Augustine, FL
- Parts Used:
- WD24X10045, WD12X10061, WD01X10103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Rate chewed drain hose up.
Removed screws that held dishwasher under cabinet...pulled out DW...removed old part...replaced with new....easier than falling off a stump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauren from Atlanta, GA
- Parts Used:
- WD18X10034
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
A hole was chewed in the inlet sump by a rodent.
First thing to do is remove all the dishes or you will have an issue with broken dishes. Naturally you will need to get the dishwasher on it's front so you can get to the inlet. First remove the two screws holding the pump on to the frame of the machine. They are long and in a tight spot so a ratchet wrench works best, I think they were 8mm but maybe 10. Next take the clamp holding the pump on the sump. Give the pump a slight pull and it will come off, and set it out of the way. Next look for another clamp. Disconnect it. Finally you will look at the top where the sump goes into the actual washer itself. There are two "U" shaped clamps holding it on. From behine they will look like U's that are facing each other while laying on their side like this. (o) They are holding the sump on and their are two bolts in each. Once again, a ratchet wrench works best. Remove those bolts and give the sump a pull and it comes right off in your hands. Then reverse the steps and put it back together. Also ensure you cut the water off under the sink, to reduce the mess. Hope it helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Colchester, VT
- Parts Used:
- WD21X10247
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken touch pad & main board
Removed broken parts, installed new parts. Instructions were excellent (well illustrated and complete).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from The Villages, FL
- Parts Used:
- WD26X10053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Leak from motor output/pump input shaft
Cut power and water flow to the appliance. Laid appliance on its side, removed the electrical lead from the motor. Remove the mount from the back of the motor and loosened the two clamps- one to the sump and one to the discharge tube. Removed and replaced the pump/motor assy. with the new one, reinstalled the clamps, rear mount and electrical lead. Righted the unit and fired it up. Worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Union, KY
- Parts Used:
- WD12X10354, WD02X10169, WD12X10198, WD12X10197, WD22X10046
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Spray holes clogged
Replaced the middle spray arm and bearing using a nut driver.
Was this instruction helpful to you?
Thank you for voting!