DDW550B-48 General Electric Dishwasher - Instructions

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

Just put the part on.

I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.

Simply screwed in new cap

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

The new rollers snapped into place on the rack, by simply pushing them in. I was able to do it by hand, my wife could not do the same, so you might use some pliers.

First I removed the four screws holding on two metal panels to gain access to the springs. Then I unhooked the broken assembly from the springs. Then I hooked the new assembly to the hinge. Finally, I reconnected the assembly to the springs. (I didn't have to unhook the assembly from the hinge because it had already broken off.)

This part must be one of those that commonly goes because I had replaced the other side about a year ago. The most difficult part a year ago was diagnosing the problem and figuring out how the pieces fit together. This now it was a quick repair because I knew exactly how to fix it. (And thanks to PartSelect for delivering the part in 48 hours even though I didn't pay for quick delivery.)

pretty easy, take off 7 screws from inside door

only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)

My suggestion is to replace all four rollers at the same time since they are all the same age. Fortunately, four rollers come in each pack you order. You need to remove the end cap on borh metal rack rods which takes a little doing. You cannot just pull the caps off. You need to twist the end cap to free up the little catch at the rear of the end cap. Once the end caps are off, just pull of the old rollers and install the new ones, replace the end caps and you're done.

Put on a new cap.

Unscrewed old one and installed the new one.

Replaced door seal and corner seals. Be sure to heat door seal in dryer be for instillation, 2 minutes. Makes for an easy installation.

over time the upper rack axles broke so the rack would just come out of the rollers. I ordered the parts from here and had to youtube how to get the stops out so I didn't have to unscrew the metal guides out making an easy job into a hard one. all you have to do is with a flat head screw driver is slightly bend the plastic end part of the stop which is in the metal guide that stops the wheels from coming out of the guides. once you bend out the plastic end you then turn the stop to get it out of the metal guides. if you youtube it its very easy. just be easy when you bend the plastic piece because I can see it breaking. I didn't break mine so the job was very very easy and took all of about 5 to 10 minutes to complete the entire job. I love this site it had real life info to help out when you need to do a job and trouble shoot your appliance.

The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.