FGCD2444SW2A Frigidaire Dishwasher - Instructions

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

Isolated the leak and found the nut had split thereby allowing a loose seal and water penetration. Ordered 2 nuts just in case the other goes and the installation was easy. Unplug the unit, remove baseplate, remove screws under the countertop, and slide the unit out a bit. Use needlenode pliers to remove terminal connection and replaced nut. Reverse it for assembly. 3 minutes tops $6 later it is done. Easy money saved by a DIY.

I ordered a new Arm Control. I unsnapped the old arm control and snapped a new arm control part in place. Took less than a minute.

Just unscrew the sprayer top, which Is 3 pieces, but should be one. Take new part, which all 3 pieces come as one piece, screw to the inside top of dishwasher and all done.

Unscrew the old spray arm, screw on new spray arm. That’s it. Simple.

Inserted springs into corresponding holes.

Removed and installed

Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.

I unscrewed the housing for the spray arm and screwed in the new housing and spray are part. It took less than a minute and works perfectly.

I removed the three screws that held the stem assembly in place, removed the old stem assembly and replaced it with the new one. Replaced the screws and began using the dishwasher again.

First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.

This was great! Removed 3 screws, took out old broken part, set in new part and screwed tight! 1 2 3 and done. Very Fast shipping less than 24 hrs.. WIFE IS HAPPY. Ted W.

Removed 3 screws, swapped parts - done. Wonderful feeling and saved a service call. Works great.

The bottom spray arm would not turn or fall off the stem assembly, so the dishes would not come clean like usual. The spray arm connects to the stem assembly via two plastic prongs that secure the spray arm. I removed the spray arm from the socket (no tool required) and observed the prongs had worn completely away. I grabbed the power screw driver and removed the assembly (3 screws). I placed the new assembly in place, secured the screws, and attached the spray arm. Finished.

Just unscrew old one and screw in the new one Very Easy