FFBD2406NW11B Frigidaire Dishwasher - Instructions

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

Replacement was every bit as simple as the website said it would be.

Took me about 2 minutes to repair, no tools to repair, very easy installation repair!

Easiest repair EVER!!! You just pull the old spray arm off (be sure to keep all the smaller pieces that click it into the bottom of dishwasher) and pop the new one in. Done!

Unsnap old and snap on new

The original lower spray arm had one end break loose the metal retainer end. I used a temporary small hose clamp to fix as I waited for the new lower arm to arrive.

The design is very easy.... pull up on the OLD and then just push DOWN on the new arm into the bottom.

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.

I removed the bottom drawer and glass trap in order to remove the old melted down washer arm. Once those parts were removed I was able to easily secure the new replacement be ensuring that it was turned enough and fit down securely (side note, if you don't hear the arm click or snap into place, it isn't secure). The part works just fine, but sadly I think I have another problem with my washer, but I will figure it out.

My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

So purchased new arm, trap and lower arm support and put in together correctly. Easy peasy all the parts snapped in place using no tools. I'm a 70 yr old gramma and no problem. Just wish I put it back together correctly the first time and saved myself the money. Never know what you can do until you try. Parts came super fast too.

It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.

Eventually broke off old heating element to get it out

The first sensible thing to do is to find the circuit breaker for your dishwasher and switch it off so as not to short anything (or yourself) out. Next, remove the lower piece of metal bracket from beneath the door by unfastening the two sheet metal screws (a nut driver or a screwdriver will do the job), taking note as to how it comes off so as to facilitate replacement. Some will recommend loosening the screws at the top from beneath the counter and pulling the machine forward a bit to gain access to the sides but, if you have a small enough hand (as I do), you can just reach in there and and hook the spring into place. I didn't want to risk loosening any plumbing! You'll need a flashlight to see where the ends connect. And, if one spring is still intact, you can reference that to reassure yourself you've got it right. I was able to stretch the spring out by hand and hook the thing to that little plastic gadget that pivots when you open the door. That's it! Button her up! You're done!

Repair man gave indication that it would cost 2-300 dollars to fix!! We looked into new and found your site. Decided to try it!! Glad we did!! Easy fix for less than $200 and it works!!! Thank you!!!