FFBD2406NB10B Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from DOTHAN, AL
- Parts Used:
- 5304517203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower swivel arm broken
Unsnap old and snap on new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BAY SHORE, NY
- Parts Used:
- 154430501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door Spring broke
Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from BELLEVILLE, IL
- Parts Used:
- 5304512731
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No power. Power surge took out the whole board
Just so simple take out the Phillips screws take off the cover three screws hold on the board. Un plug the connectors place the new board in and replace the screws. Simple plug and play.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andre from La Mirada, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking Dishwasher
The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from Sacramento, CA
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water Leaking from Bottom of Door
Replacing the part was easy. Just pop the old one out and pop the new one in. This item fixed my leaking door problem. The old arm had fallen against the heating element, which burned a hole through the end. Water was shooting out that hole and leaking under the bottom door seal. Replacing the door seal did not help, but replacing the arm fixed the leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fort Washington, MD
- Parts Used:
- 154662601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher door strike piece broke. Door had to be propped closed each time dishwasher was used.
Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from PENTWATER, MI
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower sprayer arm melted after being lodged
Pulled the old one off and pressed the new one on (plastic clips hold it on). Dishes much cleaner now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lora from Shelter Island Heights, NY
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking underneath dishwasher
My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Woodburn, OR
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking at the front, just below the door
I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from NEW KENSINGTN, PA
- Parts Used:
- 5304506525
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Replace filter in dishwasher
Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Miami, FL
- Parts Used:
- 5304507405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken wheel on upper rack.
Replacement was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaSonya from GREENVILLE, MS
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The lower dishwasher arm was a replacement for the previous one.
I removed the bottom drawer and glass trap in order to remove the old melted down washer arm. Once those parts were removed I was able to easily secure the new replacement be ensuring that it was turned enough and fit down securely (side note, if you don't hear the arm click or snap into place, it isn't secure). The part works just fine, but sadly I think I have another problem with my washer, but I will figure it out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from FREEHOLD, NJ
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Edge metal broke away from the melted tabs
The original lower spray arm had one end break loose the metal retainer end. I used a temporary small hose clamp to fix as I waited for the new lower arm to arrive.
The design is very easy.... pull up on the OLD and then just push DOWN on the new arm into the bottom.
The design is very easy.... pull up on the OLD and then just push DOWN on the new arm into the bottom.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from HARRISBURG, IL
- Parts Used:
- 5304532206, 5304532235, 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Was not draining. Found blockage, tiny pc of plastic. Put it back together wrong pcs melted on heating element
So purchased new arm, trap and lower arm support and put in together correctly. Easy peasy all the parts snapped in place using no tools. I'm a 70 yr old gramma and no problem. Just wish I put it back together correctly the first time and saved myself the money. Never know what you can do until you try. Parts came super fast too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from EVERETT, WA
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Heating Element was corroded.
It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.
Was this instruction helpful to you?
Thank you for voting!