FFBD2406NS9B Frigidaire Dishwasher - Instructions

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.

I removed the bottom drawer and glass trap in order to remove the old melted down washer arm. Once those parts were removed I was able to easily secure the new replacement be ensuring that it was turned enough and fit down securely (side note, if you don't hear the arm click or snap into place, it isn't secure). The part works just fine, but sadly I think I have another problem with my washer, but I will figure it out.

The original lower spray arm had one end break loose the metal retainer end. I used a temporary small hose clamp to fix as I waited for the new lower arm to arrive.

The design is very easy.... pull up on the OLD and then just push DOWN on the new arm into the bottom.

My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

So purchased new arm, trap and lower arm support and put in together correctly. Easy peasy all the parts snapped in place using no tools. I'm a 70 yr old gramma and no problem. Just wish I put it back together correctly the first time and saved myself the money. Never know what you can do until you try. Parts came super fast too.

Pump motor kit changing the pump went good little tough to get the old one out And the new one went in a little tough really had to push hard to get it in but it works great took longer to take out the dishwasher and put it back in instead of changing the actual part

Had to shut electricity off and turn water off and disconnect them both. Take the screws out from underneath the counter. Slide out the unit disconnect the filler tube in the back disconnect the hose and replace and repeat the process to put it back together.

It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.

The first sensible thing to do is to find the circuit breaker for your dishwasher and switch it off so as not to short anything (or yourself) out. Next, remove the lower piece of metal bracket from beneath the door by unfastening the two sheet metal screws (a nut driver or a screwdriver will do the job), taking note as to how it comes off so as to facilitate replacement. Some will recommend loosening the screws at the top from beneath the counter and pulling the machine forward a bit to gain access to the sides but, if you have a small enough hand (as I do), you can just reach in there and and hook the spring into place. I didn't want to risk loosening any plumbing! You'll need a flashlight to see where the ends connect. And, if one spring is still intact, you can reference that to reassure yourself you've got it right. I was able to stretch the spring out by hand and hook the thing to that little plastic gadget that pivots when you open the door. That's it! Button her up! You're done!

Excuse me, as I do not know all the correct nomenclature, but I hope you get what I am saying. The new spray arm would not thread on to my dishwasher water supply coming out of the top of the box. Every time I would try, the supply line would push back up into the housing. Probably need to fix that too, but then I would have to uninstall the DW and just don't have time for that. My old part would thread right on, no problem, but the connection holding it all together was wore out. So I took the new arm and the old "nut" and put them together. They threaded right on, I pulled down on the arm and it is secure. So I had to Frankenstein it a little, but my DW is working, I didn't have to tear it apart and reinstall it, and I didn't have to replace it. Win Win!

Repair man gave indication that it would cost 2-300 dollars to fix!! We looked into new and found your site. Decided to try it!! Glad we did!! Easy fix for less than $200 and it works!!! Thank you!!!

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!