FBD2400KS3B Frigidaire Dishwasher - Instructions

removed the remnants of the old wheels and popped the new ones on....simple

Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!

Removed bottom plate and heating element brass nuts. Disconnected heating element. Connected new one then replaced brass nuts. Put bottom plate back on. Very easy.

Alighned the bracket and pushed in.

One Roller detatched and hit the heat coil and melted. Both of the Spring Linkages borke. It's was quite obvious they were made not to last long. My Husband did the repairs. Thank you for asking.

1. Bottom door gasket removed very easy by grabbing left corning and pulling out. Starting with notch on right side, slide the hard plastic side up at a slight angle to catch the slot the gasket will seat in. Slowly moving toward the left, push gasket into seated position. Notch in gasket will make sure it is in correct position. Push gasket all the way in so that it is flush with bottom edge of door. Watch when first sliding gasket in, it has to g at a slight up angle or it will fall into an empty space.
2. Remove Tub gasket by gripping one side and pulling out. Replace in same fashion making sure the angled wedge of gasket is first part that lays flat in slot. Working from one side to the other, make sure the gasket seats completely. Trim excess if necessary.

I will make a few additions to the other instructions, which are great and let me see that the job was doable. To the tools needed, add pipe tape.
1. Shut off water supply.
2. Removed inlet water hose where it connects to the valve assembly. (This was a pain on my machine—too little room for the wrench, you may have a better tool—but I did get it out, slowly.)
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection (Look for your red and blue wires on the connector, my red was to the top of the solenoid, and reattach with the same grounding) from the solenoid. (This step was a great bit of information; It allowed me to see that I could do the following steps with ease, That is, the unit dropped down where you could work on it.)
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical connection to new valve solenoid.
6. Remounted assembly to the frame.
7. Re-attached the inlet water hose to the hose adapter connection on the valve. (I had to take off the L shaped connector at the bottom of the old valve and add it to the new valve. This was an extra step that required two bigger wrenches to hold the old assembly and unscrew the L joint. I just needed the extra leverage to get the old off and the new on. I am referring to the copper connection that connects to you water supply)
(8) The new valve had a slightly different configuration than my old. The rack it sits on was about an inch or so longer. This meant that I had to readjust my copper pipe just a bit to match up when it was reassembled. No big deal, I had lots of pipe length to work with. Actually, moving the valve a bit further back made more room for the wrench to work—very happy about that. In addition, the hose attachment went from a left exit to a back exit. Doesn’t seem to matter.
(9) Turned on the water, washed some dishes. (Took me about an hour, mostly because of the difficulty with the wrenches. Otherwise—piece of cake)

Removed old arm from elment. then replaced with new one.

Remove water supply, take off two screws, attach new part reconnect water supply.

After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.

Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.

Water leak solved...

Pulled out old gasket from bottom of door with needle nosed pliers and then put in new one in.

Removed the bottom panel on the unit (2 screws hold it on) and pulled the dishwasher out about 4"--after turning off electricity to the unit. Removed the broken spring and the old linkage and replaced them with the new parts. Pushed the diswasher back into place, and replaced the bottom panel. Turned on the electricity and the diswasher door is "good as new." This is quite simple to do; just takes patience.

I removed the dishwasher from the cabinet space (two screws) and manually replaced both springs. I replaced one spring first to see if there would be an improvement when the second new spring was installed. There was much better tension once the second new spring was added.That is why changing both springs is recommended. This was very easy.
Changing the gasket was scary because I thought the the whole door would have to be taken apart. You know nothing ever goes back together the same. I feared that I would create an even bigger leak than what I had. Taken the door apart didnt work for me, so I just pulled the old gasket by hand and pressed in the new one. I made sure that it was seated correctly. Voila no leak.
The dishwasher is running as good as new.
I ordered these parts on Friday morning. They were on my door step Monday morning,
I highly recommend ordering from this site.

Unscrewed dishwasher from cabinet and pulled out about 1 foot. Took bottom plate off of dishwasher. Undid clamp on hose of discharge of inlet water valve and removed hose. Shut off water to water inlet valve and removed. Took wiring clip off of water inlet valve. Removed 2 screws holding water inlet valve in place. Installed new water inlet valve in reverse order.

Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), match direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.