FBD2400KS4B Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- GILBERT from PHOENIX, AZ
- Parts Used:
- 5304518927
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old spray arm melted
Just snapped part on and works great. Lowered temp in dishwasher so not to melt the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Sacramento, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket leak
First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Mogadore, OH
- Parts Used:
- 5304518927
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Old spray arm melted
I used a screwdriver to remove melted spray arm. Then snapped the new spray arm into place. It was an easy repair thanks to the correct part from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray D from LAWRENCEBURG, TN
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Leak at door
As shown on you tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristina from SANGER, TX
- Parts Used:
- 5304518927
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lower arm had come loose and rested on the heating element, thus melting it.
Take out the old arm, and snap in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from EVERETT, WA
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Heating Element was corroded.
It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Jane from Niles, MI
- Parts Used:
- 809006501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
dishwasher was leaking onto the floor
We received the part in just a day or two so thank you for quick delivery. The base of the dishwasher door was leaking...not the actual gasket but a long strip at the base of the door had separated. With the help of a talented neighbor, my husband and our good neighbor pulled the dishwasher out from its installed place, took off the door and found a screw which needed a star-shaped screwdriver. Fortinately another neighbor had just the right tool....so screw was removed, old strip pulled out, new strip slid into place, door re-attached, dishwasher shoved back into place and anchored as though everyone knew what they wre doing! It works fine now....a small leak continued the first few washings but all is perfect now. We hope it lasts....and lasts.....and lasts! Thanks. Happy Wife
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Attleboro, MA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dishwasher leaking water on my hardwood floor
I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!
Greg
I also scored big points with the wife on my handyman repair! Thanks Partselect!
Greg
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from PORT ORCHARD, WA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Brass nut split down its side , why ???????
Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from LOVINGTON, NM
- Parts Used:
- 5304509753
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
No problems encountered
There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MIDDLETON, ID
- Parts Used:
- A00104102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
a part of the latch broke off causing the latch to not secure the door
on a U-TUBE repair sequence it showed removing the entire front panel of the door. With this Kenmore model the front panel is in two parts. The upper part where the controls and latch are is independent of the front panel so all I needed was to unscrew the upper panel, unscrew the latch, pull off the wires and reinstall by plugging in the wires, screwing the new latch to the door, reinstalling the panel to the door. It took about 15-20 minutes for the entire operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from SHELOCTA, PA
- Parts Used:
- 809006501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Leaking water
followed online video provided and it was a snap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kip from PHELPS, NY
- Parts Used:
- 5304518927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
arm fell and melted against heat coil
put new arm in place on bracket. Perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary A. from Akeley, MN
- Parts Used:
- 154701001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leakage under door.
Followed instructions with parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from SPOKANE VLY, WA
- Parts Used:
- 5304518927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spray arm had come off and melted on the heat coil
New piece snapped right on
Was this instruction helpful to you?
Thank you for voting!