FBD2400KW9B Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Racquel from Lake Charles, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing roller made it difficult to move rack.
The new roller just snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Largo, FL
- Parts Used:
- 154430501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door Spring broke on one side.
Well, first of all I want to thank you for letting me know there were two springs and also for showing the two springs because I had almost ordered from another site the official Frigidare site which did not show the other spring, the right one. I would have ordered the wrong spring. I got a spring from you with shipping (very fast Fed-X) for the price of their spring alone. Also, your site was very helpful in explaining how to put it on and advised to get two which I intended to but only ordered one, It was so easy. Beaucoup thanks!
Was this instruction helpful to you?
Thank you for voting!
Dishwasher Leaks At Heating Element. Missing Door Spring
I removed the wires from the heating element. I removed the 2 brass nuts that had split down the side. I replaced them with 2 new brass nuts. Tightened with a wrench. I then installed the missing door spring. The repair itself took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marcus from NORMAN, OK
- Parts Used:
- 5304518927
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Spay arm came off hit the heater and burned a hold in the side
Easy just snapped on works going again like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ANDERSON, IN
- Parts Used:
- 5304518927
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Spray arm came off, got melted
Snapped the new spray arm in place.
Works like new!
Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Washington, DC
- Parts Used:
- 5304518927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Some of the silverware slip thru the silverware holder. During the drying cycle the exposed silverware was to close to the arm and melted an area of the arm which caused water to seep out onto the kitchen floor.
To remove the spray arm just squeeze the sides pull up and replace the new lower spray arm in it's place. Just push down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mackenzie from MADISON, WI
- Parts Used:
- 5304518927
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Our dishwasher spray arm got stuck on a rogue dish and melted on the heating element
The spray arm simply clips to a base in the center of the dishwasher tub. The repair takes 30 seconds - the lower rack slides out, twist the base of the old spray arm to lift it off, and snap the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from TAUNTON, MA
- Parts Used:
- 5304518927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water leaking, spray arm melted
This dishwasher is pretty old and I live in a rental. When I moved in, the dishwasher leaked every time and it would had been nearly impossible to get the landlord to do any work. I read other repair stories on partselect and figured out it was the spray arm assembly. At some point the arm got detached and laid on top of the heater coil. Once it was melted and the water holes were distorted, the water shot at the door in some way to leak out the front. I replaced the part by just pushing the center part until it clicked on the bottom---- no tools were needed! The dishwasher works like a champ now. The dishes get clean the first time and no leaks on the floor. I read from other comments that the part was blue and it didn't match the original color. That wasn't as important as having a functional dishwasher. The delivery was delayed because of the health crisis, but once the warehouse sent an email that the part was shipped, I received it as was promised. All in all, I was pleased with the service and part. If there is another situation in the future, I would definitely consider using partselect again. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from PT CHARLOTTE, FL
- Parts Used:
- 5304518927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower spray arm came off and melted on the header coil
took old one off by hand, snaped the new one in place by hand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from HAYESVILLE, NC
- Parts Used:
- 5304518927
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Spray Arm melted easy replacement
Popped it in and done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Clinton, OH
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking tub seal
Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from MEDANALES, NM
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Sprang a Huge Leak
I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from N ROYALTON, OH
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
The heating element (ring) showed signs of wear
I followed the steps on YouTube.
Was this instruction helpful to you?
Thank you for voting!