FBD2400KW6B Frigidaire Dishwasher - Instructions

My husband and dad actually did the repair, but my husband not being a handy guy said it was, 'so easy, anyone could do it!' He was very nervous about taking on the project, the longest part was testing to make sure it worked(running a cycle).
The simply pulled out the dishwasher, after disconnecting all electrical power, drained the rest of the water that we couldn't see from above, following the video given took out the old part without needing to take out the motor and were able to replace the drain pump, put everything back together besides sliding it into place in case it didn't work, in less than 15 minutes! When the short cycle finished and the water had drained they put it back into place and ran an energy saver cycle and it worked like a charm! Since then(2 weeks ago) we have now ran every function and have had no issues! Every time we open the dishwasher we comment on how much we missed having a dishwasher! Haha!

First point of leakage was the door. Turns out that a gasket at the bottom of the door functions as a wave trap. As the bottom sprayer spins it sprays against the door and creates a small wave of water this gasket was starting to disintegrate, it was letting water surge over the small tray at the doors bottom. Easy to replace just pull down and remove press fit on inside door bottom. Only when this was replaced did I find the real leak but not until I guessed at the tub seal as the leak. Very hard to see where the water really comes from! Turns out it was not the tub seal but a clip that holds the heater element got smashed down from a dropped dish rack at some earlier time and this caused the heat to increase at the clip and eventually heat the clip to extent it melted the tub directly under it. JB Weld to the rescue and we have a waterproof tub again. Well almost! The tub gasket resisted my best efforts to seat correctly and thus required a new tub gasket, still hard to seat but after 2-3 attempts we have a winner. Total cost about 50 bucks vs. 6-700 for a new unit. Wife is happy!!

My daughter held the flashlight steady as a rock as I hooked not one, but two new hinges in place. Throughout the whole ordeal neither of us complained or lost our resolve. We conquered!

I followed the previous repairers instructions.
-Remove the screws around the door panel
-Remove the door panel face
-disconnect the wires
-reconnect wires to the new Latch Assy
-tighten the screws and reassemble the door panel.

Used pliers to remove old seal. Keep seal in position, note the notch facing the hole. Align the new seal, press it in, the notch helps align. Mine slipped in easy

Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps.
installed new hose.

It only took about 20 minutes to replace. Thanks for the video.

Just slid the new rack in place. Your service in locating the proper rack was excelent. I had a very bad experience with "appliance zone" prior to contacting your company so I was very happy with your great service. Thank you

Removed the 6 screws from top section inside door. Pulled control panel from front side of door. Removed two screws holding latch assemly unit and pulled 4 wires from connection. Attached the 4 wires to new door latch assembly and screwed back into place. Replaced the control panel and attached with 6 screws. Couldn't get any easier.Great service Quick delivery.

Followed the YouTube instructions. Loosened 4 screws took off the front door panel and removed the old door and installed the new one. The video was very helpful!

I read the instructions that others had posted and completed the repair in less than 5 minutes!

After moving the dishwasher out from the cabinetry, I removed the screws holding the pump in place. Pulling the pump from the formed plastic opening, I found a toothpick lodged in the pump housing. At the same time I noticed that the front o-ring was deformed due to being the incorrect size (too large). It was installed at the factory this way.

I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.

I watched several videos of people replacing this gasket easily, but we had trouble. The old one came out easily. The new one just slipped into the crack, but it kept going and ended up on the inside of the door. We ended up taking the outside panel off to get the gasket out. We tried to fit the thing into the slot, but it kept coming out the other side. I finally came across someone who had had the same trouble. By feel only, you can feel a slight ridge on the top side of the lower door and I had to press the gasket against that ridge. It was not a very noticeable ridge, but it holds the back (slot edge) against the door so that the gasket stays put. When we figured that out, the repair went smoothly. I am running the dishwasher now and so far, so good.

Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.

Replaced upper wash blade and used screwdriver to pop off rail stops to slide rack all the way out to exchange