DGBD2438PF6A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MARK from PORT ALLEN, LA
- Parts Used:
- 154844301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace dishwater pump.
Block and remove water hookup and drain hose. Ensure drain port on garbage disposer has a plug in it while drain hose is disconnected to ensure sink water does not find its way inside the cabinet. Place dishwasher with door facing floor. Remove electrical plug and pump retainer. Slide out pump. To replace pump reverse steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Bonaire, GA
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper Spray Arm kept falling off.
The new arm came preassembled. I unscrewed the old arm base with my hand and screwed the new arm in place. The whole process took less than a minute. The new part was not made the same way. It was better than the original. Must have been a problem from the manufacturer. WORKS GREAT!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette from Fort Lauderdale, FL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Racquel from Lake Charles, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing roller made it difficult to move rack.
The new roller just snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phil from lindenhurst, NY
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
spray arm broke
Just unscrew old one and screw in the new one Very Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from EAST ISLIP, NY
- Parts Used:
- 5304532950
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A piece of the upper rack began to rust out
Used the screwdriver to pry the upper rack left side tine up and out. Slipped the new one into place and pressed hard to seat the tine. this process took all of about 20 seconds to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from FT LAUDERDALE, FL
- Parts Used:
- 5304500204
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water leak
watched a video, really easy fix. Solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from MARINE ST CRX, MN
- Parts Used:
- 5304532199
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaked spot free fluid
Replaced part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from ESTERO, FL
- Parts Used:
- 140229954072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rusty and crumbled areas in upper dishrack
Just watch installation video. Finished repair in abut 30 minutes. Honestly, great service and fast delivery from this company. Please add the contact info to your favorites
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Linthicum Heights, MD
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
spray arm broke free from mount
unscrewed and remove the original mount....this is only hand tight. install new spray arm, hand tight only, threads are plastic and could strip if over tightened.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Brandon, SD
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper spray arm kept falling off
This part fixed problem. The original part seemed to have a defect. Was simple to fix, simply took off old piece still connected and hand tighten the new piece on, it took about 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Alamogordo, NM
- Parts Used:
- 140229954072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Top rack had rusted
Slid the rack out, removed the end pieces holding top rack in the sliding arms. Removed the spray arm. It was stiff & a bit hard to get off, but with a little careful prying it came off. Put that spray arm assembly back onto the new rack, slid the new rack back in place, put the end pieces back on and in less than 15 minutes, we were done. Part came in very quickly, I might add. I feel like I have a brand new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cumming, GA
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper spray arm separated from arm retaining nut.
VERY simple repair - just unscrew the retaining nut by hand and hand screw on the new spray arm and nut assembly. A 30 second fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Perry from Waynesboro, VA
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper spray arm kept blowing off
Easiest repair ever. The spray arm itself usually really is not the problem, it usually is the clip or gasket that holds the spray arm on. It wears out. This part is perfect for it supplies a new spray arm, nut and gasket/clip. I think it wears out due to a build up on the arm that puts too much pressure on the clip/gasket. Remember when taking the nut off, if you are standing above the unit with your arm inside, you turn the nut clockwise while looking down. Good luck.
Was this instruction helpful to you?
Thank you for voting!