FDB1450CHB4A Frigidaire Dishwasher - Instructions

The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!

I went to your website found part# and parts diagram and ordered parts . I picked standard shipping . That evening e-mailed me they were instock and shipped also gave tracking # thet parts were here the next day.I removed the front dec panel then the 4 nut& bolts holding door to hinges(with door in closed position).Then I removed the 2 screws holding the hinges to the frame/axle. Replaced hinges with new ones .Put screws back in frame/axle . Put 4 nut and bolts back to secure door to hinges . Then i reinstalled under counter put new wheels on lower rack . I then filled it with dishes and ran a long cycle checked for leaks THEIR WERE NONE!!! THANK GOD !! Job complete, Thanks parts direct for a well designed website and detailed pics and parts#. TIM

The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

Removed old filters and trap and installed new ones.

After being told by a repairman that it would be cheaper to replace the dishwasher than to fix the handle I found this sight. When the part came in I simply removed 6 screws for the control panel. Once that was off the handle assembly was connected by two screws that required a different tool (allen wrench). I removed those screws unplugged the 4 contacts that connected to the old assembly. Plugged them to the new part and reversed the process with the screws. Works like it is new and I am oh so glad to prove the repairman wrong!!!

New right away when we heard the sound, the spring broke. Easy to replace, pull dishwasher out from under countertop, usually held in place by two screws into countertop. Remove screws, pull out dishwasher. Close door, springs will now have the most slack in them. One spring located on each side. Remove spring from one side and replace with new spring to ensure proper spring placement. No actual tools needed as spring rests on a bracket attached to door and other end of spring goes through hole in bottom of dishwasher rack. open door to test for tension as there are several holes to choose from. .

Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.

Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

Simple repair.

I ordered a PS12365196 BOARD from PartSelect that arrived in 2 days, a few lights came on but still did not work, next I called back to get the PS8689162 Control Assembly, (this took another 2-3 days) this has the buttons on the front that usually light up when you set up and run the dishwasher. Still no luck so i had to try and understand this as there really isn't much more to the control of the device. Went back in, by now I can take this apart in about 5 minutes, replaced the original control board and it stared right up! Called PartSelect and a few minutes later confirmed the return of the 1st part which did not seem to work. Got to go as my email just arrived with return instructions...

Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.

Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!