FFID2423RS2A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janice from ELK GROVE, CA
- Parts Used:
- 5304506521
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Plug for soap dispenser.
My future son in law did it. Looked at instructions on the app for the part. Didn't take very long.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERTA from FAIRBANKS, AK
- Parts Used:
- 5304532229
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
wheels break or bend or fall off
if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex from COMMERCE, GA
- Parts Used:
- 5304500204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom door seal leaking on my dishwasher
Still have a slight leak, but I'm thinking it may just need time to seat itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SUNBURY, PA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
the end on one of the door springs on the dishwasher broke off
I removed the access panel using a nut driver. One fastener on each side at the lower front panel. Move the two piece lower panel and set aside. Locate the broken spring. It will be on the floor under the dish washer. Remove the broken spring. Place the new spring end in the hole in the chord end and place the chord over the plastic guide. Use a pliers to stretch the spring and fasten it to the hole in the lower dishwasher frame at the back of the dishwasher. Check the door for proper tension. Replace the lower panel and secure with the two screws. I recommend replacing both springs at the same time to insure proper balance. If you only replace one spring you will be replacing the other in the near future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Collierville, TN
- Parts Used:
- 5304500204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom seal on door came out and melted on heating element.
Took me about 2 minutes to repair, no tools to repair, very easy installation repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhiannon from FEDERAL WAY, WA
- Parts Used:
- 5304517203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old sprayer arm melted to heating coil.
Easiest repair EVER!!! You just pull the old spray arm off (be sure to keep all the smaller pieces that click it into the bottom of dishwasher) and pop the new one in. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from DOTHAN, AL
- Parts Used:
- 5304517203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower swivel arm broken
Unsnap old and snap on new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SHICKSHINNY, PA
- Parts Used:
- 154844301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Faulty pump
Replacement was every bit as simple as the website said it would be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from KESWICK, VA
- Parts Used:
- 154252701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
several issues with dishwasher
Easy fix but not cheap
replaced drain trap and four rack wheels with clips
All parts were expensive for the items.
found cheaper wheels w/clips for much less on another site.
replaced drain trap and four rack wheels with clips
All parts were expensive for the items.
found cheaper wheels w/clips for much less on another site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert C from COTTONWOOD, AZ
- Parts Used:
- 5304535382
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old basket developed holes and needed replacing.
Took the old out and placed the new in its place. That simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from KENDALLVILLE, IN
- Parts Used:
- 5304506517
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Replacing grommet
Finally we laid in the tub--be sure to support the lid. The grommet could be inserted halfway. Then trying to fold the grommet back we were able to use a screwdriver to force the rest in to place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MARSHALL, MI
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
Water inlet tube had worn a hole in it
Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from FREEHOLD, NJ
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Edge metal broke away from the melted tabs
The original lower spray arm had one end break loose the metal retainer end. I used a temporary small hose clamp to fix as I waited for the new lower arm to arrive.
The design is very easy.... pull up on the OLD and then just push DOWN on the new arm into the bottom.
The design is very easy.... pull up on the OLD and then just push DOWN on the new arm into the bottom.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaSonya from GREENVILLE, MS
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The lower dishwasher arm was a replacement for the previous one.
I removed the bottom drawer and glass trap in order to remove the old melted down washer arm. Once those parts were removed I was able to easily secure the new replacement be ensuring that it was turned enough and fit down securely (side note, if you don't hear the arm click or snap into place, it isn't secure). The part works just fine, but sadly I think I have another problem with my washer, but I will figure it out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from NEW KENSINGTN, PA
- Parts Used:
- 5304506525
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Replace filter in dishwasher
Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.
Was this instruction helpful to you?
Thank you for voting!