MDR251RER0 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from Sacramento, CA
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
waher would run if we figeted with the handle and then stoped working(found a popcorn kernal broke the handle switch)
shut off the power on the breaker box, 6 screws inside the door on the tolp and side,pulled 4 wires off, 2 star head screws on the unit. took bad unit off,put new one on and put the screws back in.
5 minutes
5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Ozone Park, NY
- Parts Used:
- 154043802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom trim peice was badly twisted and bent.
The dishwasher was already lose so laying on it's back was easy. Two phillip screws were all that held the piece in place .... and the replacement was a simple slide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Milford, PA
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door latch broke
Removed the screws that held the cover on, then removed the 2 screws that held the door latch in place. Disconnected the broken door latch and attached the new one. Put all the screws back in and that was it! Also, the shipment of the part was SO QUICK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Camby, IN
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch handle broke
Removed the screws holding the door panel and as the sheet said was the way the it went. Two screws holding the handle latch and replaced it and put the door back on. There was 4 wires to replace on the latch. Replaced the gasket and the job was done. All in all it was a very good experience with good instructions and very good same day shipping. A VERY GOOD EXPERIENCE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from MEDANALES, NM
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Sprang a Huge Leak
I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Arvada, CO
- Parts Used:
- 5300809909
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
heard a noise while dishwasher was in operation, opened door and noticed the dishes were dry, no water was spraying out and dishwasher was making a whirling noise.
After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Falls Church, VA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Half the wheels were missing from the lower rack.
So easy it shouldn't even count as a repair, really. The dishwasher, there when I bought the place, had a lower rack that wouldn't roll out as it should. That's because there were no wheels on the left side.
The rack lifts out easily. These wheels snap on to small protrusions from the wire rack.
The rack lifts out easily. These wheels snap on to small protrusions from the wire rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chardon, OH
- Parts Used:
- 154637401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Dishwasher ran through cycle but no water ever entered the washer.
Turned off water & pulled plug from electrical outlet. Two screws removed the lower cover, two more screws hidden behind the opened door allowed the removal of the bottom panel. Laid a towel under the valve on the lower left to catch water & disconnected the inlet fitting with a 1/2" wrench. Remove the two screws holding water inlet valve next. With valve loose, remove electrical connector and drain hose (pliers). Valve has an elbow fitting that will need to be removed and installed on new valve - use Teflon tape or paste for a leak-free assembly. Reattach the drain hose & electrical connector before installing the valve using the two screws. Once in place, re-attach the inlet fitting (no Teflon required on tapered seats) and make sure everything is tight. Test washer through one cycle for water flow and no leaks. If all is good, remove towel and tools, then re-install the two lower panels. Clean up and you are done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from East Stroudsburg, PA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken rack rollers
Two rollers on the lower rack were missing and one was flattened. I popped off the bad roller and snapped the three new rollers in place, all by hand. Took about 60 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Bryan, TX
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle latch broke after 10 years
Opened it up, replaced, closed it back. Didn't bother installing the gasket since that's still in good shape.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Elkton, MD
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two wheels broke off
Snapped new wheels into place on the axel. New wheels were exactly like the old ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Troutman, NC
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken door latch assembly
This repair turned out quite easy. I removed the 6 phillips head screws that held the door latch cover in place, dropped the cover and let it hang while I removed the latch assembly that was held in place by two torx head screws. I used needle nosed pliers to gently disconnect the wiring connectors from the old latch assembly one at the time, then carefully attached the wire to corresponding lug on the new latch. Once all wiring was transferred, I installed the new latch using the two torx head screws, replaced the cover, and reinstalled the 6 phillips head screws to secure the cover. There was no need to replace the gasket, so I'm holding on to it for future use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Charlotte, NC
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heating Element Seal and Nut
Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dana from sunderland, MA
- Parts Used:
- 5304442175
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle was broken
1. turn off power
2. put an old blanket on the floor under the opened door.
3. unscrew six phillips screws (it's not necessary to unscrew all the screws, only the ones at the top)
4. remove two torque screws securing handle
5. remove handle
6. unplug four leads one at a time transferring leads to new handle in the same location
7. replace two torque screws
8. replace six phillips screws
2. put an old blanket on the floor under the opened door.
3. unscrew six phillips screws (it's not necessary to unscrew all the screws, only the ones at the top)
4. remove two torque screws securing handle
5. remove handle
6. unplug four leads one at a time transferring leads to new handle in the same location
7. replace two torque screws
8. replace six phillips screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Los Angeles, CA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack got hung up & wouldn't roll
I snapped on the new roller and bingo! problem solved.
Was this instruction helpful to you?
Thank you for voting!