FDB2415LFB0 Frigidaire Dishwasher - Instructions

I unscrewed and removed the old Arm-Control fixture. I had a little (very little) trouble figuring out how to fit the gasket. It didn't go on like i thought it should. There was no gasket on the original fixture. So I put it on the way I thought it should go. I then screwed the new Arm-Control fixture on to the outlet. That was it. No tools required.

unscrewed old spray arm, installed new arm. Took less than 30 seconds.

Remove 3 screws from stem assembly. Swapped the old for the new, replace screws. Installed and lock lower wash wand. Fixed in 5 min. Great service and prices. My wife thanks you. (Had to hand wash dishes for a few days) thanks

Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.

Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)

Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.

Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.

Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks

The only difficultpart was to figure out how to remove the stainless cover from the door. Seems it slides upwards after screws are removed. After that it is self explainatory and goes back together in 5 minutes.

DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

This was pretty easy. It was a guess as to the problem, but there much debate , if the water isn't moving it had to be the pump, right?. So i replaced the circulation pump. 2 screws on the top and two trim screws on the bottom, and it slides right out. Then UNPLUG IT.. Take the screen out of the bottom on the inside and make sure you get all the water out or it will end up on the floor when you tip it on it's side. The directions were ok, i looked over them briefly but didn't use them. tools were, phillips srewdriver, torx driver (pump bracket srews) wire stripper/crimper (for the plug adaptor) and a heat gun, (for the heat shrink tube for the crimp connection). Overall it was pretty easy. the pump was made to be easy to replace. 45 min and back in action.

Replaced the entire top rack with spray bar.

The unit would not pump the gray water out so I immediately assumed it was a bad pump. Ordered the part and had it the next day. After taking things apart I realized it was a clogged discharge hose and the original pump was still good. Since I had the new pump and everything was already disassembled I decided it would be a good insurance policy to replace the pump anyways. Easy to install. I didn't even have to pull the unit out. Just did it from underneath.

lift off yhe old one and snap on the new one

remove vanity panel
disconnect copper supply line from valve
remove valve mounting screws
rotate valve to access hose clamp
loosen clamp and slide up rubber tubing about 2 inches
pull hose off barbed fitting and remove old valve
reverse order with new valve

I took the bottom parts out. This can basically be done without tools. You need a phillips to unscrew 3 screws to remove the stem. Then easily replace with the new one. Putting the spiny washing part was kinda weird because I was afraid to break the nubs off again. I took the whole bottom carriage out so I could see better, pushed down kinda hard and twisted the right way (figure out which way needs to be twisted before hand by looking through the bottom of the stem).

Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.

For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it with silicone caulk, but may have to replace that - looks easy, .

Took the dishwasher out removed the two screws and the part holding the motor in and removed the motor. Received the parts, places o'rings on the motor, which came with the kit, even though I ordered the two o'rings. Replaced the motor, installed the part that holds the motor and tightened the screws. Cut the old connector off the dishwasher and replaced it with a new connector that came with the kit. Reinstalled the dishwasher, works great. Thanks for your Site.