DW1800Y0 Frigidaire Dishwasher - Instructions

Removed the screws that hold the panel on ( just the top ones-no need to go all the way down the sides. Need a "star" headed screwdriver to remove the switch itself. Then removed the wires (4),one be one, so as not to mix them up. reinstalled all thescres for the switch, then the panel. Job done.
What amazes me is that Frigidaire doesn't read your page to realize that the handle assembly was defective and send out a recall. look at all the repars listed in your site , and these re just from the people that have responded with comments and who use your service. New handle/switch is much more sturdy with a higher density plastic that the original. Your service is easy to use, prompt and accurate. Fixed the dishwasher while my wife went to the store. Dishwasher done in 15 minutes and watched theNCCA tournament for 2hours in complete peace !!!!! No need to tell the wife only spent 15 minutes.

It was a walk in the park. Unscrew the six screws in the back of the panel to reach the latch. Unscrew the two torx screws in the front of the latch and replace each of the cables, one by one, in the new latch in the same order. Put the screws back into place in reverse order and... voila, wthout a single shock !!

Before starting I disconnected the dishwasher. First I removed the door cover which then exposed the interior part of the door. I then used a star bit on the screwdriver to remove old latch. I disconnected the four wires to the door making sure that I made a point of which wire was connected to what. I then inserted the new latch and reconnected the wiring. Finally, put on the door panel and screwed in the remaining screws. About 15 minutes total work time.

Removed the front cover by unscrewing the 8 screws. Removed the latch and attached new one. Re-attached front cover, and it works fine.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.

Important - turned the power to the dishwasher off. took the screws out of the top part of the back door panel. pulled the wire leads of the broken switch, replaced the switch with the new one, reconnected the wires, put the panel back on.
Fixed

Just pushed it onto the rod that held the old one

First, I located the dishwasher switch in the circuit breaker and turned it off, so as to kill power to the dishwasher - DO NOT PROCEED WITHOUT DOING THIS FIRST. Unscrewed front panel by removing 6 screws on the inside of the door frame. Then pulled 2 white wires on left and 2 black wires on right off of bottom of latch. Then used hex wrench to remove 2 hex screws holding handle and latch to frame. Then reassembled in reverse order as I disassembled. Note that there was a video on the site when I ordered the part, and it demonstrated all the steps; however, when I received the part and went back to the site to review the video again, it was gone. I'm glad I paid close attention the first time I watched it as it was extremely helpful and showed me exactly how to complete the installation.

Watched installation video and followed directions. All went smoothly.

Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.

Removed six philip head screws to remove upper half of the dishwasher door unit to access handle, then remove handle by remove two star screws and for wires connectors. Installed in reverse.

Note:
I was very impressed on how quick I received the part after it was ordered.

After watching the repair video, it was 'easy as pie'. I would have thought the gasket was too long and cut it off if not for the video. Thank you. Saved a great deal of money not having to have a repair person do the work. I strongly recommend watching the video.

Removed the screws holding the door panel and as the sheet said was the way the it went. Two screws holding the handle latch and replaced it and put the door back on. There was 4 wires to replace on the latch. Replaced the gasket and the job was done. All in all it was a very good experience with good instructions and very good same day shipping. A VERY GOOD EXPERIENCE.

I replaced this latch,but noticed that the electric terminal configuration was not identical to the old original part. There were no installation instructions furnished for installing this new part, so I had to guess that the wire terminals attached to the new part in a similar position as detached from the old part. So far the renter has not called that the dishwasher is not operating correctly.

The repair was pretty straightforward. If somebody is attempting, they should make sure that screws close the bottom part of the door should be opened. You only need to open the top 4 screws.

I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.

PartSelect is a life saver and I saved lots of money by not having to call a repairman.