PLD4375RFC3 Frigidaire Dishwasher - Instructions

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.

New one snaps into place easily.

Unsnapped three clips in lower rack securing old fence in rack. Attached clips to new fence and snapped assembly back into rack.

Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings (~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

Pulled out old gasket and shield guards and put in new ones. No tools needed. Piece of cake??

unscrewed the old upper arm spray nut off and rescrewed the new one on....very easy...then I took the old gasket out of the bottom of the door and replaced by sliding it in. very simple....less then 15 minutes for both and have solved my issues.

Remove 3 screws from stem assembly. Swapped the old for the new, replace screws. Installed and lock lower wash wand. Fixed in 5 min. Great service and prices. My wife thanks you. (Had to hand wash dishes for a few days) thanks

Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!

unscrewed old spray arm, installed new arm. Took less than 30 seconds.

I unscrewed and removed the old Arm-Control fixture. I had a little (very little) trouble figuring out how to fit the gasket. It didn't go on like i thought it should. There was no gasket on the original fixture. So I put it on the way I thought it should go. I then screwed the new Arm-Control fixture on to the outlet. That was it. No tools required.

The only difficultpart was to figure out how to remove the stainless cover from the door. Seems it slides upwards after screws are removed. After that it is self explainatory and goes back together in 5 minutes.

DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

Removing the old rack was accomplished by removing the grey retainer clips located at the end of the silver rack guides. This allows the entire upper rack to slide out of the guide tracks. Unless you purchased all of the additional parts associated with the rack you must remove the needed old parts such as the spray arm, plate guides, wheel assemblies, etc. to complete the replacement and reassembly. Each of these pieces are "snapped on" by clips that are removed with moderate difficulty. Mostly due to the apprehension that you are going to break them, however, with only the pressure exerted by your fingers they will snap off and will go actually go back on easier. The order you remove and replace the various parts is your choice. The exact positioning of the parts back on the new rack is critical, so if your memory is not good, take a quick photo with your cell phone for reference. The only tool I used was a small screwdriver to separate the clip when I first removed the rack, but in retrospect I could have removed it by hand. The key thing to remember is do not apply excess force when trying to remove the old parts, just direct pressure with your fingers. Good luck, it took me only about 15 minutes from start to finish. The best part is I probably saved $150.00 by doing it myself, figuring service time for a repairman, plus his mark-up on the parts.

FRIDGEADAIRE - GALAXY SERIES -Part arrived within 3 days of order BUT it was wrong part. All excited about getting the upper wash rack in full operation once again. Pilled shelf out to remove gasket to find it looked nothing like the one on there. The part I need is like a bellows of sorts that fits on the water line attached to the upper shelf. The part received goes on the back wall.
Now i am back at square one with part I don't need and hoping for the part I do need