PLD4050RHC0 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carolyn from TUCSON, AZ
- Parts Used:
- 154580301
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher was not draining
Followed the instructions given on the video, for replacing the drain pump. I did not pull the unit all the way out of the counter space just pulled it out about a foot. I had to lie on the floor to change the pump. That cost me some time for removal and installation, but I did not have to disconnect any water or electrical lines. I did unplug the power. The exchange went smoothly accept for the one spring clamp. Hard to squeeze and slip on. Would have been better to use a different kind of clamp. I have arthritis so that was an issue. All in all a good experience. A Big Thank You !! to this site . There instructions were perfect, the site is very user friendly. They saved me the cost of hiring a repair person. I'm a 75 yr. old disabled female, if I can do it then you surely can.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from STILESVILLE, IN
- Parts Used:
- 5304523304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad code OU came on screen
Pull out shut off power unscrewed fan.Replaced with new fan . Rest power and shoved back in ran cycle. All was fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CASA GRANDE, AZ
- Parts Used:
- 154637401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable), Wrench set
leak at water control valve
Completly disconnected and layed dishwasher on its side for better access. New valve support was 1 inch longer than original but created no problem. it took no more than 30 min. to complete job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from KENDALLVILLE, IN
- Parts Used:
- 5304532204
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Replacing grommet
Finally we laid in the tub--be sure to support the lid. The grommet could be inserted halfway. Then trying to fold the grommet back we were able to use a screwdriver to force the rest in to place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MARSHALL, MI
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
Water inlet tube had worn a hole in it
Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MOUNT AIRY, MD
- Parts Used:
- 5304507405, 5303943103
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
One screw that held the roller would not hold as the hole in the case was stripped. I knew when I removed original as there was material in the screw threads
I used both epoxy on the male threads and then pulled out the case and twisted the flat car body flat kind of a nut. Let it sit for 36 hours and now like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Lakewood, WA
- Parts Used:
- 154637401
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
no water entering the dishwasher
turned off electricity, pulled dishwasher out about a foot, turned off water too dishwasher, removed inlet valve and replaced it with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERTA from FAIRBANKS, AK
- Parts Used:
- 5304532229
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
wheels break or bend or fall off
if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Austin, TX
- Parts Used:
- 5304532200, 5304532229, 5304507405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Wrench set
Broken wheels, Caps and Brackets. Couldn't hold dishes or wash right.
Just use a hexagonal driver to remove the Upper rack roller, screw the new ones in, place caps on the rail ends, and pop the new wheel on with some pliers! Simple and fun!
Was this instruction helpful to you?
Thank you for voting!
Spring on Door Broke
I took the door off by removing the two screws that hold the it in place. I removed the two screws that secures the diswasher to the cabinets. I slide out the unit approx 3 inches. I attached the new spring and linkage (very simple to see how it connects).
I pushed the unit back in, secured it to the cabinet and put the door back on.
That's it! Easy. I saved at least $150 service call with Sears.
I pushed the unit back in, secured it to the cabinet and put the door back on.
That's it! Easy. I saved at least $150 service call with Sears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from FALLBROOK, CA
- Parts Used:
- 809006501, 8581548276014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Missing tub gasket
I think the videos on the site are awesome. Made both repairs after watching them. They explain the repairs in a simple to follow way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert C from COTTONWOOD, AZ
- Parts Used:
- 5304535382
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old basket developed holes and needed replacing.
Took the old out and placed the new in its place. That simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from STURBRIDGE, MA
- Parts Used:
- 140222632022
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Parts rusting
Open door, Lift out old ,replace with new.
Was this instruction helpful to you?
Thank you for voting!
broken springs on door
pulled of dishwasher a couple of inches,
installed springs
pushed dishwasher back
done!
installed springs
pushed dishwasher back
done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Rockledge, FL
- Parts Used:
- 154580301
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Noisy Drain Pump
The drain pump was making a high pitched buzzing noise which told us that its days were numbered. When I ordered the pump I found out that the dishwasher was really made by Electrolux for Whirlpool. Taking the pump off was a simple matter of removing two hose clamps and prying the pump off the frame. The hard part was realizing that it just pulled off without damaging anything. The new pump easily slipped right in and the screw in hose clamp was easily installed. However, the hose clamp that required pinching with the pliers was not that easy. I had to use a screwdriver to push it all the way on while holding the clamp open with the pliers. All in all pretty easy.
Was this instruction helpful to you?
Thank you for voting!