FPHD2491KF0 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christine from PILLAGER, MN
- Parts Used:
- 5304475625
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Sick of old ones jump out
Wheel, no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- oscar from WOODBRIDGE, VA
- Parts Used:
- 5304507354
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken lid of the detergent dispenser.
The video show a different model, the only difference is that the screws for the top part shouldn't be removed only the ones that hold the front. Replace the detergent dispenser once the cover is removed is easy. All works like brand new. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from BRIGHTON, MI
- Parts Used:
- 5304475622
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fence corroded
Less than 1 minute to remove old part and install new fence
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teri from N RICHLND HLS, TX
- Parts Used:
- 5304475618
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper dishwasher rack rusted
Upper dishwasher rack easily removes off roller arms with upward tilt. Upper water tube/spray arm assembly unsnap from old rack and snaps onto new rack... no tools needed. Lucky enough new height adjustment levers come with new rack and with firm push they snap into place also. Stemware holder also unsnapped off old rack and then snapped onto new rack. Upper rack returned to dishwasher with upward tilt and threaded back on roller arms. Easy peasy. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEPHEN from MYRTLE BEACH, SC
- Parts Used:
- 5304475618
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Replace rusted upper dishrack on Frigidaire Professional dishwasher
1. Watch YouTube videos, even though they're different model dishwashers. NOTE: all replacement racks are not OEM, they're cheap imitations, thinner material, not original design for holding dishware.
2. Replace rusted upper rack, rack simply lifts out; no need to remove rail end caps.
3. Carefully remove attachments from original basket ( no tools were required), be especially careful detaching the upper spray arm from the underside of the basket.
4. Attach previously removed original attachments (not all would fit because of replacement rack design). Attach upper spray arm.
5. Reinsert replacement basket into upper rails.
2. Replace rusted upper rack, rack simply lifts out; no need to remove rail end caps.
3. Carefully remove attachments from original basket ( no tools were required), be especially careful detaching the upper spray arm from the underside of the basket.
4. Attach previously removed original attachments (not all would fit because of replacement rack design). Attach upper spray arm.
5. Reinsert replacement basket into upper rails.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Lorton, VA
- Parts Used:
- 5304507354
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rinse aid dispenser leaking and empty after 4 wash cycles
Needed to replace detergent / rinse aid dispenser unit on the inside top of door.
1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.
2) Mark and disconnect the four (4) wires connected to the dispenser unit. The connections were so tight, it required pliers and a screw driver to loosen them.
3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.
4) Position new unit through interior. Screw in place.
5) Re-attach four (4) wires in same sequence as disconnected.
6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.
1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.
2) Mark and disconnect the four (4) wires connected to the dispenser unit. The connections were so tight, it required pliers and a screw driver to loosen them.
3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.
4) Position new unit through interior. Screw in place.
5) Re-attach four (4) wires in same sequence as disconnected.
6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from CHICO, CA
- Parts Used:
- 5304475637
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
main motor assy keeps seizing up this will be the 4th motor
unplug dishwasher.turn water valves under sink off. remove water line from dishwasher at hot water valve. remove evacuation hose from drain.remove support brackets securing dishwasher to counter top. slide dishwasher from under counter. put a sandwich bag over water line and drain line and secure with a rubber band so they don't leak onto floor. turn machine upside down. unplug motor wiring pigtail. remove 4 screws remove motor. reverse process to install. suggest using a silicone lubricant on o rings for easier install. took old motor apart found front bearing seized due to faulty front seal. hopefully this has been upgraded.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VERSAILLES, KY
- Parts Used:
- 5304507354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Would not dispense dish washing tablets
Turned power supply off to dishwasher Opened door and removed screws holding font of door Unplugged soap dispenser and removed six screws. Popped out and installed new dispenser. Plugged wires into new dispenser and installed front of door. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIMOTHY from ELBURN, IL
- Parts Used:
- 5304535382
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old basket had a hole
Lift out old basket replace with new basket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Meridena from GROSSE PT PK, MI
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
filter was clogged uo and silverwate basket was damaged
Located a YouTube video and it was easy to remove and clean the filter and install the basket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FREDERIC from PITTSBORO, NC
- Parts Used:
- 5304535382
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken cutlery holder
open door
place holder in the sliding component
close door
place holder in the sliding component
close door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnie from Aztec, NM
- Parts Used:
- 5304507354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dispenser would not dispense.
Removed 4 screws on door cover, 6 screws on dispenser 4 wires and reinstalled new one. Done less than 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Garden City, NY
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
silverware basket cracked and broken--utensils falling through
received part the next day. great service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Winterville, NC
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Portions of the bottom of the center basket melted out not long after purchase.
The entire assembly drops into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from CHICO, CA
- Parts Used:
- 5304475637
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
motor began to get noisey then stopped woking completly
Unplug the dishwasher. Turn off water supply. Use adjustable wrench to take off water supply line, the take off the drain hose. remove any mounting brackets holding the dish washer in place. Slide it out, the lines & plug should come out with it. Place dishwasher on it's back. I have a bad back, so I set it up on a work bench. Remove 4 screws & 1 screw holding the ground wire. remove the motor. You may have to pry a little. Install new pump, I put a little lube on the o rings. Gently work it in place using the 4 mounting screws. Reconnect ground.Reverse process to reinstall dishwasher
Was this instruction helpful to you?
Thank you for voting!