FGBD2451KF0 Frigidaire Dishwasher - Instructions

It would sometimes work, which led me to believe it was a switch. Looked on line and found the mail switch to go on was in the latch. I took it apart, 6 screws, wiggled the switch and it went on. So I found the door switch to be bad. It was very simple to change the switch.

Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.

Water leak solved...

After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.

Pulled out old gasket from bottom of door with needle nosed pliers and then put in new one in.

I found the parts needed on Part Select and read comments by users. I took the suggestion to buy both springs at the same time and the door linkages too. Although they were pricey, the parts arrived in a few days and were absolutely perfect. To my suprise and delight, the entire fix for the broken spring and link and the opposite spring and link were easily accomplished in less than 10 minutes. The links just hook directly onto a small hook on the door and the springs have specially bent ends that fid the linkage and then the adjustable length holes on the door. It made me feel quite manly for about fifteen minutes as I made everyone in the house open and close the dishwasher door several times.

Unscrewed upper sprayer by hand, screwed new one in by hand. Piece of cake!

Unscrewed the old spray arm and replace with the new spray arm.

The best part was in the ordering process. Having the diagrams with the parts let me see that I was ordering the correct part. Thanks!

The spray arm comes off into 3 parts but is really only supposed to be one. I removed the nut from the old assembly and attempted to place the new assembly on by hand. The new nut seemed to be slightly smaller than the original so it would not attach to the dishwasher. Using a kitchen knife, I removed the new nut from the arm unit and attached the new arm to the original nut and it went back on easily. The connection of the new arm to the new nut was 3 tabs that needed to be depressed with the knife and was a different conection method than the assembly that kept coming off in the wash cycle. The replacement part had a much better design than the original.

I replaced the basket. No tools necessary. New basket seems sturdier than original. Very satisfied with my purchase.

I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes

Unscrewed dishwasher from cabinet and pulled out about 1 foot. Took bottom plate off of dishwasher. Undid clamp on hose of discharge of inlet water valve and removed hose. Shut off water to water inlet valve and removed. Took wiring clip off of water inlet valve. Removed 2 screws holding water inlet valve in place. Installed new water inlet valve in reverse order.

Discovered upper wash arm had come off. It looked like it was repairable, but the bushing/clip holding the arm came off after one wash. Looked on line and reviewed part and saw it was a one piece assembly from photos. Removed old assembly by unscrewing from top of washer and screwed new assembly in place.

Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), match direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.

Removing the old rack was accomplished by removing the grey retainer clips located at the end of the silver rack guides. This allows the entire upper rack to slide out of the guide tracks. Unless you purchased all of the additional parts associated with the rack you must remove the needed old parts such as the spray arm, plate guides, wheel assemblies, etc. to complete the replacement and reassembly. Each of these pieces are "snapped on" by clips that are removed with moderate difficulty. Mostly due to the apprehension that you are going to break them, however, with only the pressure exerted by your fingers they will snap off and will go actually go back on easier. The order you remove and replace the various parts is your choice. The exact positioning of the parts back on the new rack is critical, so if your memory is not good, take a quick photo with your cell phone for reference. The only tool I used was a small screwdriver to separate the clip when I first removed the rack, but in retrospect I could have removed it by hand. The key thing to remember is do not apply excess force when trying to remove the old parts, just direct pressure with your fingers. Good luck, it took me only about 15 minutes from start to finish. The best part is I probably saved $150.00 by doing it myself, figuring service time for a repairman, plus his mark-up on the parts.

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job