FDB4315LFB3 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alina from Orange, CA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking
I read the instructions that others had posted and completed the repair in less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Pat from CAVE CREEK, AZ
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom of Silverware gone,silverwear went to bottom of dishwasher
Your service was great, the basket came in two parts and all I had to do was put the two together and put it in the dishwasher. I am glad we were able to get a new one. Thanks again for such quick service. Thank you very much for such great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from PALM SPRINGS, CA
- Parts Used:
- 809006501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The bottom door gasket was loose and leakage was occurring from the door
Followed the YouTube instructions. Loosened 4 screws took off the front door panel and removed the old door and installed the new one. The video was very helpful!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from TUMBLING SHLS, AR
- Parts Used:
- 809006501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Our Frigidaire dishwasher leaked from the lower left side.
I watched several videos of people replacing this gasket easily, but we had trouble. The old one came out easily. The new one just slipped into the crack, but it kept going and ended up on the inside of the door. We ended up taking the outside panel off to get the gasket out. We tried to fit the thing into the slot, but it kept coming out the other side. I finally came across someone who had had the same trouble. By feel only, you can feel a slight ridge on the top side of the lower door and I had to press the gasket against that ridge. It was not a very noticeable ridge, but it holds the back (slot edge) against the door so that the gasket stays put. When we figured that out, the repair went smoothly. I am running the dishwasher now and so far, so good.
Was this instruction helpful to you?
Thank you for voting!
Noisy, vibrating pump
After moving the dishwasher out from the cabinetry, I removed the screws holding the pump in place. Pulling the pump from the formed plastic opening, I found a toothpick lodged in the pump housing. At the same time I noticed that the front o-ring was deformed due to being the incorrect size (too large). It was installed at the factory this way.
I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.
I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Bridgeton, NJ
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking out of door seal. Sent PartSelect the brand and model number of the dishwasher and they did the rest. The replacement part was exactly the same as the old part. Delivery was fast and efficient. Only took a few minutes to replace and the dishwasher is back in running condition
Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- elner from new concord, KY
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic piece that held the arm on was worn & dishwasher only 2 yrs old.
Arm screwed on and immediately fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERTA from FAIRBANKS, AK
- Parts Used:
- 5304532229
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
wheels break or bend or fall off
if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert C from COTTONWOOD, AZ
- Parts Used:
- 5304535382
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old basket developed holes and needed replacing.
Took the old out and placed the new in its place. That simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from Keota, OK
- Parts Used:
- 5304525218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water did not drain. Found the door latch broken
Unplug dishwasher. Open the door. Remove two Phillips head screws holding the door panel on. Slide door panel down and out to remove. With door still open, remove the six T20 torque screws that hold the control panel. Behind the control is the latch assembly. Take a picture of the wires going into the latch assembly for installation reference(mine was black wires on left and white wires on right). Unplug the two sets of wires. Remove two T20 torque screws that hold the latch. Replace with new latch and reverse steps for installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from STILESVILLE, IN
- Parts Used:
- 5304523304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad code OU came on screen
Pull out shut off power unscrewed fan.Replaced with new fan . Rest power and shoved back in ran cycle. All was fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FAIRHAVEN, MA
- Parts Used:
- 5304525218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door wasn’t locking
You tube video and it was so easy less than 20min had it fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Rockledge, FL
- Parts Used:
- 154580301
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Noisy Drain Pump
The drain pump was making a high pitched buzzing noise which told us that its days were numbered. When I ordered the pump I found out that the dishwasher was really made by Electrolux for Whirlpool. Taking the pump off was a simple matter of removing two hose clamps and prying the pump off the frame. The hard part was realizing that it just pulled off without damaging anything. The new pump easily slipped right in and the screw in hose clamp was easily installed. However, the hose clamp that required pinching with the pliers was not that easy. I had to use a screwdriver to push it all the way on while holding the clamp open with the pliers. All in all pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from KENDALLVILLE, IN
- Parts Used:
- 5304506517
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Replacing grommet
Finally we laid in the tub--be sure to support the lid. The grommet could be inserted halfway. Then trying to fold the grommet back we were able to use a screwdriver to force the rest in to place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CASA GRANDE, AZ
- Parts Used:
- 154637401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable), Wrench set
leak at water control valve
Completly disconnected and layed dishwasher on its side for better access. New valve support was 1 inch longer than original but created no problem. it took no more than 30 min. to complete job.
Was this instruction helpful to you?
Thank you for voting!