FDB1050REB5 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tony from Lavallette, NJ
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dishwasher was leaking
I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Providence, RI
- Parts Used:
- A00126501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
dish washer would not drain.
I pulled out the internal filter and assorted washer parts. All in good shape. I bailed out the washer and removed the pump assembly from under the washer. I pulled it apart to inspect impeller. all looked fine. Plugged pump in and turned on pump cycle. Pump did not operate as it should have and I ordered new pump. My daughter put it back together and all is working well now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Wisconsin Rapids, WI
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Door leaked water
The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Shoreview, MN
- Parts Used:
- A00126501
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The relatively new Frigidaire (Electrolux) dishwasher would not drain the water out of the base of the washer. The pump impeller assembly was making a "rattling" sound and wasn't pumping
I ordered the replacement pump from Partselect and it arrived 3 days later. The new pump went in very simply with two mounting screws (don't over tighten!!) and the two hose claps for intake and discharge. It works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Avon, IN
- Parts Used:
- 809006501
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Gasket bottom of door
Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from TULSA, OK
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower arm came off and melted.
Simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Freehold, NJ
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Interior bottom door gasket seal broken
Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Lafayette, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels on lower rack melted
Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LONNIE from NORTH LAS VEGAS, NV
- Parts Used:
- A00126501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
water would not drain
cleared water from machine with bulb type basting tool. Placed two large bath towels on floor in front of machine. Removed machine to floor laying it on the towels on its left side. Removed pump. Installed new pump. Reinstalled machine. Worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Marne, MI
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bottem door gasket was shot and leaked
Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Minerva, OH
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The small "nubs" on the assembly had worn off.
After several years of use and cleaning the small "nubs" that held the locking peice on the assembly under the jet arm had worn off. This allowed the whole thing to spin and the dishes weren't getting clean. Finding the part on the site was easy, it arrived amazingly fast and all is up and working great. I have used Parts Select 2 or 3 times in the past and have always had the same great results. Saved me a bunch in repair bills. Thanks
Was this instruction helpful to you?
Thank you for voting!
Dishwasher wasn't cleaning properly
I just did the repair just like the video suggests to fix it. I disconnected the power cord, shut off and took apart the water inlet line, and drain line. Unscrewed the top of the washer from the cabinet and pulled out the dishwasher. Tilted the washer to better get to the bottom and took off the connecting wires (red and white.) Unscrewed the brass nuts holding the heating element and removed the element from the machine. Took out the bottom sprayer arm. Replaced the element, replaced the brass nuts and connected the wires back up. Put the sprayer arm back in. Pushed the machine back into place and re-secured the top to the cabinet. Hooked all water, drain, and power lines back up and all was good again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thresa from Waukesha, WI
- Parts Used:
- 154252001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper spray arm falls off during the wash cycle
My upper spray arm attaches to the upper dish rack. It comes in four parts: the spray arm, the bracket which attaches it to the rack, the water funnel, and a plastic nut that holds the pieces together. The nut was worn and wouldn't hold so I replaced that piece and it works great. It took less than one minute to fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danise from Brentwood, TN
- Parts Used:
- 809006501
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwasher leaked at the bottom of the door
First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WOODWAY, TX
- Parts Used:
- 154701001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher leaking splash shield was cracked
Watched your video repair was easy.
Was this instruction helpful to you?
Thank you for voting!