FDB1500LFC1 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the nut holding on the element would not tighten. leaked at the location where the nut was located
Removed the cover at the front bottom to gain access to the nuts holding on the element.
Turned off dishwasher breaker.
Removed the wires connected to the element.
With a 1/2" wrench, removed the element mounting screws.
Removed the bottom rack.
Removed the lower spray arm.
Removed the element from 2 clips.
Removed the element.
Put the new element in place.
Clipped it in.
Put new screws on and tightened up with a wrench. Not too much but enough to squash the washers to make a tight seal.
Replaced wires.
Replaced spray arm and bottom rack.
Turned on the breaker.
Ran it through a cycle to check for leaks.
Replaced bottom cover.
Turned off dishwasher breaker.
Removed the wires connected to the element.
With a 1/2" wrench, removed the element mounting screws.
Removed the bottom rack.
Removed the lower spray arm.
Removed the element from 2 clips.
Removed the element.
Put the new element in place.
Clipped it in.
Put new screws on and tightened up with a wrench. Not too much but enough to squash the washers to make a tight seal.
Replaced wires.
Replaced spray arm and bottom rack.
Turned on the breaker.
Ran it through a cycle to check for leaks.
Replaced bottom cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Panama City Beach, FL
- Parts Used:
- 5304535768, 140229954072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper and Lower Racks on Dishwasher were rusting.
Ordered the parts, put into place and that was it...very easy...had to undo the upper rack spinner wash blade but was easy to remove and put back onto the new rack...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathey from Humboldt, TN
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom spinner wouldn't stay on
VERY simple---unscrewed three screws on the broken part (the little nubs that held on the bottom spinner were broken off), screwed the new one back in, re-attached the spinner.
I was VERY pleased with the customer service and quick shipping (ordered on Sunday night, the part was delivered Wednesday morning). I would definitely recommend this site to anyone, and would use it again. Five Stars!!!!
I was VERY pleased with the customer service and quick shipping (ordered on Sunday night, the part was delivered Wednesday morning). I would definitely recommend this site to anyone, and would use it again. Five Stars!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Louisville, TN
- Parts Used:
- 140229954072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the rack had broken on one of the arms that connect to the wheel in the slider
I unclipped the plastic pieces at the front of the rack. This was very easy. Then I removed the old rack. I then removed the water sprayer from the old rack and placed it on the new rack. This was simple and I unscrewed the water sprayer by hand and snapped out. Putting it on the new assembly was very easy. Then I placed the new rack on the two stainless steel sliders and refastened the plastic clips at the ends. It was no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Billings, MT
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
worn out seal
Used pliers to remove old seal. Keep seal in position, note the notch facing the hole. Align the new seal, press it in, the notch helps align. Mine slipped in easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Wellington, FL
- Parts Used:
- 154662601
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Strike plate on dishwasher broke.
Removed damaged strike plate from dishwasher and screwed new part into place. Tested and dishwasher worked fine. Took less than 15 minutes to get the job done. Was very pleased with how fast the part was delivered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Ephraim, WI
- Parts Used:
- 154430501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken springs
My daughter held the flashlight steady as a rock as I hooked not one, but two new hinges in place. Throughout the whole ordeal neither of us complained or lost our resolve. We conquered!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from Belle Mead, NJ
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower Spray Arm damaged
1-2-3 snapped off the old and snapped on the new! New part was just as ordered and just like original! My dishwasher is like new again! Thanks PartSelect for your great price and prompt shipment!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelley from LACONA, NY
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Dishwasher hose had hole in it. It was 23 years old.
After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REBEKAH from COLUMBUS, GA
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our spray arm had fallen onto the heating element and melter
It was super simple. I popped the clips that were holding the old spray arm on and then popped the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alina from Orange, CA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking
I read the instructions that others had posted and completed the repair in less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Bridgeton, NJ
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking out of door seal. Sent PartSelect the brand and model number of the dishwasher and they did the rest. The replacement part was exactly the same as the old part. Delivery was fast and efficient. Only took a few minutes to replace and the dishwasher is back in running condition
Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Pat from CAVE CREEK, AZ
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom of Silverware gone,silverwear went to bottom of dishwasher
Your service was great, the basket came in two parts and all I had to do was put the two together and put it in the dishwasher. I am glad we were able to get a new one. Thanks again for such quick service. Thank you very much for such great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from PALM SPRINGS, CA
- Parts Used:
- 809006501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The bottom door gasket was loose and leakage was occurring from the door
Followed the YouTube instructions. Loosened 4 screws took off the front door panel and removed the old door and installed the new one. The video was very helpful!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from TUMBLING SHLS, AR
- Parts Used:
- 809006501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Our Frigidaire dishwasher leaked from the lower left side.
I watched several videos of people replacing this gasket easily, but we had trouble. The old one came out easily. The new one just slipped into the crack, but it kept going and ended up on the inside of the door. We ended up taking the outside panel off to get the gasket out. We tried to fit the thing into the slot, but it kept coming out the other side. I finally came across someone who had had the same trouble. By feel only, you can feel a slight ridge on the top side of the lower door and I had to press the gasket against that ridge. It was not a very noticeable ridge, but it holds the back (slot edge) against the door so that the gasket stays put. When we figured that out, the repair went smoothly. I am running the dishwasher now and so far, so good.
Was this instruction helpful to you?
Thank you for voting!