DGBD2432KB0 Frigidaire Dishwasher - Instructions

Easy as pie. Just turned off water and electricity. Disconnected hoses and wires and replaced with the new valve.

Removed the bottom panel, and I had to disconnect the water supply, which did NOT use flexible tubing (much to my disappointment), removed the screws holding the diswasher in the cabinet. Slid it out, took the old springs off, put the new ones on.

It was pretty straightforward -- no big deal.

Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps.
installed new hose.

It only took about 20 minutes to replace. Thanks for the video.

Seriously very easy. Took screws from side of door on inside of washer, silver cover plate came off and was simple to replace the latch using torque screwdriver and phillips screwdriver.

Used pliers to remove old seal. Keep seal in position, note the notch facing the hole. Align the new seal, press it in, the notch helps align. Mine slipped in easy

Unscrewed the housing for the old piece and screwed on the new part. No tools needed. Easy to use website, fast delivery. Very easy.

Had to reposition the two moveable dish rack to accommodate the silverware drain rack. Very simple to do.

My daughter held the flashlight steady as a rock as I hooked not one, but two new hinges in place. Throughout the whole ordeal neither of us complained or lost our resolve. We conquered!

1-2-3 snapped off the old and snapped on the new! New part was just as ordered and just like original! My dishwasher is like new again! Thanks PartSelect for your great price and prompt shipment!

Removed 6 torx headed screw (loosens the internal control panel) and 2 philips headed screws(allows for front door panel removal). 2 torx screws had to be removed from existing latch along with 2 plugs loosened, be aware of how the plugs were connected to the latch. Do the reverse; attach plugs to new latch and reattach latch with the 2 torx headed screws. The 6 torx screws reattach the control panel and the 2 philips screws reattach the front door panel (be sure the front door panel is properly aligned prior to installation of the philips screws).

First point of leakage was the door. Turns out that a gasket at the bottom of the door functions as a wave trap. As the bottom sprayer spins it sprays against the door and creates a small wave of water this gasket was starting to disintegrate, it was letting water surge over the small tray at the doors bottom. Easy to replace just pull down and remove press fit on inside door bottom. Only when this was replaced did I find the real leak but not until I guessed at the tub seal as the leak. Very hard to see where the water really comes from! Turns out it was not the tub seal but a clip that holds the heater element got smashed down from a dropped dish rack at some earlier time and this caused the heat to increase at the clip and eventually heat the clip to extent it melted the tub directly under it. JB Weld to the rescue and we have a waterproof tub again. Well almost! The tub gasket resisted my best efforts to seat correctly and thus required a new tub gasket, still hard to seat but after 2-3 attempts we have a winner. Total cost about 50 bucks vs. 6-700 for a new unit. Wife is happy!!

After moving the dishwasher out from the cabinetry, I removed the screws holding the pump in place. Pulling the pump from the formed plastic opening, I found a toothpick lodged in the pump housing. At the same time I noticed that the front o-ring was deformed due to being the incorrect size (too large). It was installed at the factory this way.

I went online to search for new parts. PartSelect was the second or third listing on the search page. I submitted the dishwasher model number and was taken to a set of parts illustrations. I was easily able to find the o-rings I needed.

I watched several videos of people replacing this gasket easily, but we had trouble. The old one came out easily. The new one just slipped into the crack, but it kept going and ended up on the inside of the door. We ended up taking the outside panel off to get the gasket out. We tried to fit the thing into the slot, but it kept coming out the other side. I finally came across someone who had had the same trouble. By feel only, you can feel a slight ridge on the top side of the lower door and I had to press the gasket against that ridge. It was not a very noticeable ridge, but it holds the back (slot edge) against the door so that the gasket stays put. When we figured that out, the repair went smoothly. I am running the dishwasher now and so far, so good.

I read the instructions that others had posted and completed the repair in less than 5 minutes!