FDB4315LFB0 Frigidaire Dishwasher - Instructions

The parts above fell off or broke and were not covererd under warratee. I called you guys, the parts came in a few days and I snapped them on. Your service was very good.

Pulled out old gasket from bottom of door with needle nosed pliers and then put in new one in.

Unscrewed the old spray arm and replace with the new spray arm.

The best part was in the ordering process. Having the diagrams with the parts let me see that I was ordering the correct part. Thanks!

Unscrewed upper sprayer by hand, screwed new one in by hand. Piece of cake!

The spray arm comes off into 3 parts but is really only supposed to be one. I removed the nut from the old assembly and attempted to place the new assembly on by hand. The new nut seemed to be slightly smaller than the original so it would not attach to the dishwasher. Using a kitchen knife, I removed the new nut from the arm unit and attached the new arm to the original nut and it went back on easily. The connection of the new arm to the new nut was 3 tabs that needed to be depressed with the knife and was a different conection method than the assembly that kept coming off in the wash cycle. The replacement part had a much better design than the original.

I replaced the basket. No tools necessary. New basket seems sturdier than original. Very satisfied with my purchase.

Discovered upper wash arm had come off. It looked like it was repairable, but the bushing/clip holding the arm came off after one wash. Looked on line and reviewed part and saw it was a one piece assembly from photos. Removed old assembly by unscrewing from top of washer and screwed new assembly in place.

Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), match direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.

I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes

First thing I did was turn off the power to the dishwasher, then remove the racks. Remove the foot plates, remove the two top screws holding the dishwasher. Then using the socket set, retract the two foot stands to pull the dishwasher forward. You may not have to do this step as I had to get it over tile. The pully springs are on the sides, easily replaced. After replacing the springs and I recommend replacing both at the same time, put everything back. The hardest part will be the foot plates, there are two and getting them lined up and the screws back in is a bit of a challenge. Then you are done.

First turn the power off! If you have water in the tub, use something like a wet/dry shop vac to drain as much water out as possible. Removing the strainers will help get more out. To remove the smaller horseshoe shaped strainer, pull up and towards the handle. The sprayer is then removed by rotating the base of it slightly. Then you can remove the large strainer. The more water you get out the better! Then remove the kick panel. You will see the drain pump right in front of you with a white and a purple wire. Disconnect the wires by pulling their tabs towards you, and move them out of the way. With a screwdriver, loosen the worm clamp on top of the pump that connects the drain line to the pump. Have a towel handy, even if you got all of the water out, there will still be some in the line. Then take a pair of pliars (long nose may work best, or small channel locks) and compress the clamp on the black hose behind the pump, moving the clamp towards the center of the hose. The pump should now move a little. Pulling the pump towards you, wiggle slightly to try to remove the pump from its support, preferably without breaking the tabs, but keeping them intact is not critical if you are replacing the pump. More water may come out at this point, so be prepaired. Put the new pump in by reversing the process, making sure you do not break the support tabs. Slide the compression clamp into place. Reconnect and tighten the drain line, reconnect the white and purple wires. Dry your work area carefully so you can spot any leaks. Apply power, and run a rinse cycle, watching for leaks. If everything looks ok, kill the power again and reattach the kick plate. Turn power back on one last time, and enjoy your dishwasher again!

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.

New one snaps into place easily.

Unsnapped three clips in lower rack securing old fence in rack. Attached clips to new fence and snapped assembly back into rack.