FDS252RBS2 Frigidaire Dishwasher - Instructions

I unsrewed the old part and screwed the new one in the same way the old one was in.
piece of cake. anyone could do it!

First i removed the screws on the back panel, unscrewed the latch, removed the wires and installed the new latch.
I found the latch is too expensive for a little plastic part.

It was a walk in the park. Unscrew the six screws in the back of the panel to reach the latch. Unscrew the two torx screws in the front of the latch and replace each of the cables, one by one, in the new latch in the same order. Put the screws back into place in reverse order and... voila, wthout a single shock !!

Important - turned the power to the dishwasher off. took the screws out of the top part of the back door panel. pulled the wire leads of the broken switch, replaced the switch with the new one, reconnected the wires, put the panel back on.
Fixed

First dissconnect power, and remove the 6 phillips-head screws from the back/upper side of the door, next remove the 2 torx screws holding the handle assembly, and unplug the 2 micro switches attached to the handle. Reverse this procedure and you're finished. It's so easy, a caveman could do it.

I opened the control knob panel. The latch assembly is located behind inside the panel along w/ the wires. This is my second replacement of the assembly. The last one lasted about 2 years. They should make a sturdier latch assembly next time.

Removed the screws that hold the panel on ( just the top ones-no need to go all the way down the sides. Need a "star" headed screwdriver to remove the switch itself. Then removed the wires (4),one be one, so as not to mix them up. reinstalled all thescres for the switch, then the panel. Job done.
What amazes me is that Frigidaire doesn't read your page to realize that the handle assembly was defective and send out a recall. look at all the repars listed in your site , and these re just from the people that have responded with comments and who use your service. New handle/switch is much more sturdy with a higher density plastic that the original. Your service is easy to use, prompt and accurate. Fixed the dishwasher while my wife went to the store. Dishwasher done in 15 minutes and watched theNCCA tournament for 2hours in complete peace !!!!! No need to tell the wife only spent 15 minutes.

Removed the screws that held the cover on, then removed the 2 screws that held the door latch in place. Disconnected the broken door latch and attached the new one. Put all the screws back in and that was it! Also, the shipment of the part was SO QUICK!

Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.

shut off the power on the breaker box, 6 screws inside the door on the tolp and side,pulled 4 wires off, 2 star head screws on the unit. took bad unit off,put new one on and put the screws back in.

5 minutes

I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.

PartSelect is a life saver and I saved lots of money by not having to call a repairman.

Removed the rack out of dishwasher. Removed sprayer by removing 4 screws. Removed cover to pump propeller assy.by just lifting up on the cover. Then you remove 4 screws from the pump cover. Remove the propeller. Pull up on shaft and seal. Then when you replace everything just reverse the directions.

The actual installation of the dispenser was a breeze. Just unscrew the 6 screws unplug the 2 electrical wires and put the new one in. The problem I had was removing and replacing the front panel of the machine. The metal facing had corroded onto the frame of the door and was difficult to get off. Replacing the door was just as much a pain as it had to be lined up correctly with 4 holes in the frame. Did it in the end everything works great. Cheaper than a whole new machine.

I used the diagnostic tool to determine which part I needed and ordered it. After receiving the part very quickly I took off the front panel easily enough and removed the old part as per video instructions. I realized it did not look exactly the same. I wasted a good bit of time calling both the parts co. and Fridgidaire to find out that there had been numerous problems with the old part so a new part was designed differently and therefore did not look the same but should work. Reviewing the video again I installed it and Voila the dishwasher was once again operational. The big mistake is I took the complete front part of the dishwasher off which took a while to reinstall. All in all the experience was a good one. Saved me money and God knows these days every penny counts.

I actually didn't. I watched my husband replace the latch and gasket. All he used were screwdrivers to remove the panel on the inside of the door. The latch assembly had to plug in and two screens. He unscrewed, unflugged the broken unit, replaced it with the new by screwing in the two screens and plugging the the prongs into the panel. He then put the door cover back on. It took about 10 minutes and the dishwasher is as good as new!!