FDS252RBS2 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Grass valley, CA
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch broke
Six screws, two torque drive screws and, four wires.
Then reverse to install. Pull out old seal wash out groove find center mark on new seal and install be sure and fold notch on bottoms. Easy
Then reverse to install. Pull out old seal wash out groove find center mark on new seal and install be sure and fold notch on bottoms. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from St. Petersburg, FL
- Parts Used:
- 5304442175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Latch handle broke due to age and heat stress on plastic.
The repair was relatively easy and I probably saved enough money as to not have to buy another dishwasher. The part alone was $42. A service call and installation would have made it not cost effective to fix.
The control panel is loosened with phillips head screws on the inside of the door. The latch is attached with the "star" shaped screws. I did not own one of these drivers so I had to leave the house to get one. I used pliers to disconncet the clips from their connections as to not pull the wires from the clips.
The control panel is loosened with phillips head screws on the inside of the door. The latch is attached with the "star" shaped screws. I did not own one of these drivers so I had to leave the house to get one. I used pliers to disconncet the clips from their connections as to not pull the wires from the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from DENVER, CO
- Parts Used:
- 154388801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid cap fell off during the drying session and was warped as a result.
I just had to buy a new cap and screw it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from Summerville, SC
- Parts Used:
- 154388801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rinse cap was mutilated, the rinse agent leaked.
Simply unscrewed the old. Replaced with the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from PORT ORCHARD, WA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Brass nut split down its side , why ???????
Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from LOVINGTON, NM
- Parts Used:
- 5304509753
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
No problems encountered
There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Sacramento, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket leak
First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Portage, MI
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Door Latch
Removed the broken part and disconnected the four wires. Installed new part (two hex head fasteners) attached wires - good to go!
Quick delivery on the part allowed for dishwasher to be down for only a few days after the part was ordered.
Quick delivery on the part allowed for dishwasher to be down for only a few days after the part was ordered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Water Mill, NY
- Parts Used:
- 154662601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
strike was broken
Easy as pie. I tokk the screws out that held the dishwasher to the counter top out. Then removed the screws holding the strike in place, inserted the new one, installed screws and then rescrewed the 2 screws backintothe countertop. Job done. All told 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cait from ARLINGTON, MA
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Handle broke and would not latch
I followed the instructions in the video. It was really easy and took less than 15mins. Very happy with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from OXFORD, MS
- Parts Used:
- 154106202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water was leaking through the heating element Accra point.
Isolated the leak and found the nut had split thereby allowing a loose seal and water penetration. Ordered 2 nuts just in case the other goes and the installation was easy. Unplug the unit, remove baseplate, remove screws under the countertop, and slide the unit out a bit. Use needlenode pliers to remove terminal connection and replaced nut. Reverse it for assembly. 3 minutes tops $6 later it is done. Easy money saved by a DIY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette from Fort Lauderdale, FL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Stafford, VA
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Relay shorted out after diagnostics ran
Removed two screws on each side, lower half. Inside, removed six screws. Replaced the assembly and replaced all screws.
Not worth the fifty dollars for the part, just to have a door open at the right time to empty soap. Quite a hefty price to pay considering the price of the machine
Not worth the fifty dollars for the part, just to have a door open at the right time to empty soap. Quite a hefty price to pay considering the price of the machine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Racquel from Lake Charles, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing roller made it difficult to move rack.
The new roller just snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Prior Lake, MN
- Parts Used:
- 154219201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Lower repair arm failed and did not allow dishwasher to complete wash cycle. Repair completed in less than 10 minutes and dishwasher is now functional. Thanks.
remove center nut retaining the arm to the unit and replaced the arm.
replaced the nut.
complete.
replaced the nut.
complete.
Was this instruction helpful to you?
Thank you for voting!