PLD2560LCC0 Frigidaire Dishwasher - Instructions

#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.

Simple repair.

Removed the two bracket screws attaching the washer to the countertop, and removed the kick panel beneath the door. Pulled the washer out enough to access the spring arms. Replaced the broken spring arms, and pushed the washer back into it's space, re-attaching the kick plate, and securing the lock tabs on top of the washer. Used one phillips screwdriver, a #2 tip. That simple.

Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.

Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.

Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.

pulled DW out from under counter. drained water from unit. laid DW on its side. removed 5 screws from unit 2 to remove drain motor and three to remove bracket. used adj pliers to remove spring clamp and screwdriver to remove other clamp. to install i did the reverse

I just did the repair just like the video suggests to fix it. I disconnected the power cord, shut off and took apart the water inlet line, and drain line. Unscrewed the top of the washer from the cabinet and pulled out the dishwasher. Tilted the washer to better get to the bottom and took off the connecting wires (red and white.) Unscrewed the brass nuts holding the heating element and removed the element from the machine. Took out the bottom sprayer arm. Replaced the element, replaced the brass nuts and connected the wires back up. Put the sprayer arm back in. Pushed the machine back into place and re-secured the top to the cabinet. Hooked all water, drain, and power lines back up and all was good again.

After several years of use and cleaning the small "nubs" that held the locking peice on the assembly under the jet arm had worn off. This allowed the whole thing to spin and the dishes weren't getting clean. Finding the part on the site was easy, it arrived amazingly fast and all is up and working great. I have used Parts Select 2 or 3 times in the past and have always had the same great results. Saved me a bunch in repair bills. Thanks

First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!

First let me say I love this company, I have used them before and I will use them again.
Parts arrived quickly, unwrapped them, put the video
supplied by this site on my phone and the entire project was done in less than ten minutes. My dishwasher works like new. Thank you !

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!