MDB100RGD0 Frigidaire Dishwasher - Instructions

I followed directions from a video on this site and written directions in order to make the repairs. Pulled out the old gasket from one end with pliers . I cleaned out the slot in the door of any food or dirt and replaced with the new gasket. It was a very easy and quick repair that allowed me to use my dishwasher quickly. Thanks for the help.

1-2-3. Finished ! I had watched your video on how to !

Used pliers to pull out the old gasket. New gasket snapped into place. Notice where notches in the gasket are when the old one is removed, so the new one can be properly oriented. It was not necessary to remove the door.

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.

first of all, my name is virginia , I ordered the part for my husband and because of his work schedule I decided to try to fix it myself. It was very easy, about 8 screws and it was out and the new one was in and working. see, girls can do repairs ourselves.

Removed front panel of door, to get to the screws that hold the door on the hinges. Removed door, pulled gasket with pliers from bottom of door, not easy to get out because of mineral deposits. Had to push quite hard to get new gasket in. Put every thing back together and no leaks. I live in Alaska and I tried to order the part through Sears and they wanted $18.95 for shipping for a $12.87 part. The part with PartSelect was $14.92 but only $6.95 for shipping. I ordered the part on a Tuesday and recevied it on that Friday. We in Alaska get very tired of companies thinking we live on another planet. Thank you PartSelect.

removed 6 screws to take off door cover . Found two star head screws holding door latch removed them . Undid 4 wires attached to the old latch one at a time and attached in same order to new latch. I put the two star headed screws back in. secured door cover and every thing worked great.

After i identified where it was leaking i cut the vave off under sink so i could remove part. All it had was 2 screws holding it to the frame and of course the copper line. I then went online to parts select and within 2 days my part arrived,i was planning on being down for at least a week but not with part select!! Thank you all for the great service!

Replacement was simple.

Located where the dishwasher was leaking from and by referencing the parts catalog determined that it was the water valve. I ordered the part from Parts select and replaced the part when it arrived. Replacing the part was very easy and I now have a working dishwasher again.

Had trouble installing the new gasket at first. Fell inside the door, and would not stay in the groove intended for it. After watching the video on your website, learned is best to angle the gasket and work in slowly to the groove from one side. Much easier then

The first sensible thing to do is to find the circuit breaker for your dishwasher and switch it off so as not to short anything (or yourself) out. Next, remove the lower piece of metal bracket from beneath the door by unfastening the two sheet metal screws (a nut driver or a screwdriver will do the job), taking note as to how it comes off so as to facilitate replacement. Some will recommend loosening the screws at the top from beneath the counter and pulling the machine forward a bit to gain access to the sides but, if you have a small enough hand (as I do), you can just reach in there and and hook the spring into place. I didn't want to risk loosening any plumbing! You'll need a flashlight to see where the ends connect. And, if one spring is still intact, you can reference that to reassure yourself you've got it right. I was able to stretch the spring out by hand and hook the thing to that little plastic gadget that pivots when you open the door. That's it! Button her up! You're done!

Disconnected the water line. Pulled the dishwasher out from underneath the counter. Turned the dishwasher on its side. Removed the two screws that were holding the motor in place with a special screwdriver set I had to buy. Removed the motor. Found that the front O-ring on the motor was mangled. Replaced the O-ring. No more screeching. The dishwasher now cleans the dishes better than the day I first bought it. I have to wonder if that O-ring was ever installed properly from the factory.