FDB635RBS1 Frigidaire Dishwasher - Instructions

After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!

After several years of use and cleaning the small "nubs" that held the locking peice on the assembly under the jet arm had worn off. This allowed the whole thing to spin and the dishes weren't getting clean. Finding the part on the site was easy, it arrived amazingly fast and all is up and working great. I have used Parts Select 2 or 3 times in the past and have always had the same great results. Saved me a bunch in repair bills. Thanks

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

My upper spray arm attaches to the upper dish rack. It comes in four parts: the spray arm, the bracket which attaches it to the rack, the water funnel, and a plastic nut that holds the pieces together. The nut was worn and wouldn't hold so I replaced that piece and it works great. It took less than one minute to fix.

Pulled the dishwasher out from under the ounter, laid it flat on the front side, unplugged the motor, removed two screws and the retaining clip, pulled the motor straight out, oiled and put the new o-rings on the new motor, slid it in, replaced the clip and two screws, reinstalled the dishwasher, and done.

First let me say I love this company, I have used them before and I will use them again.
Parts arrived quickly, unwrapped them, put the video
supplied by this site on my phone and the entire project was done in less than ten minutes. My dishwasher works like new. Thank you !

Takes longer to open the machine and remove the lower basket than to do repair.

Snap arm and support together, align and twist in machine to lock in place.

Save yourself some time and buy the support. High risk it can be broken while being removed from the arm. I am glad I purchased a new one and didn't take the risk.

Easy

Both the door latch assembly and strike broke on the dishwasher. I was happy to find both parts available at PartSelect.com. Simply removed mounting screws so I could pull the dishwasher out, removed the old strike, disconnected the 4 wire attachments and removed the ddor latch assembly, and re-assembled with the new parts. Pretty easy job- the only unusual thing was that you need a torx screwdriver for the latch assembly.

I removed 6 screws to get to the door latch, then removed 2 screws to remove the broken latch assembly. Changed out 4 wires, reinstalled the 2 screws that attached the latch to the door,thenreinstall the 6 screws that assemble the door back together. Everything fit and works properly. Thanks guys, your service was great.

two screws, and pull unit out from under counter, turn on it's side. Two allen-head screws to remove motor retaining clip, unplug wires, and remove motor. Reassemble, using silicone grease on O-rings that seal motor. That's it.

I removed the screws on the inside of the dishwasher door to remove the front facade to get access to the door latch assembly, I think about 6 screws. Then I unscrewed the two hex screws that mounted the latch assembly to the door. I then had to un-hook the electrical wires (4 plugs, 2 on a side) from the assembly. I attached those same plugs to the new door latch, and mounted the assembly back on with the two screws, and tested the door to see if it closed, latched, and if the dish washer would run (since I unhooked and rehooked up the electrical wires). Finally I screwed the front facade back on and was done. It took about 5 minutes. I did get a small shock when I was removing the electrical plugs from the old assembly from touching the metal dish washer door and one of the plugs at same time.

I removed the screws from the inside of the door. There are also tiny screws you have to remove that holds the part onto the door. Then I was able to remove the part, unplug the power receptacles and install the new part. Very simple!!

i just took off the old and poped on the new, it was way to easy! no tools required!

After receiving my part in a timely manner, I removed the six screws holding the cover on the door. After making sure the appliance was unplugged, I removed the two star screws and removed the broken latch assembly. I disconnected the four electrical wires noting their placement. I connected the wires to the new latch assembly, screwed the assembly to the door, and replaced the cover on the door. That was one of the best quick-fix experiences I have ever had. Thanks PartSelect.com!!!!