FDS251RJR0 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Surprise, AZ
- Parts Used:
- 154637401
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water was not filling the dishwasher at the approbriate time in the cycle.
Pulled the dishwasher out, turned it on the side to gain access to the inlet valve, removed the inlet valve. The hard part was getting the valve fitting that didn't come with the inlet valve. I had to use liqued wrench to loosen the hard water deposits to get it off. Once it was off, putting the new valve on was easy. Also of note, when I tested the old vlalve with an Ohm meeter it read 8 M ohm, not infinity. The new one only measured at about 1k ohm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- linda from pittsburgh, PA
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
My soap dispenser had worn out and wouldn't stay closed anymore
Received the part quickly and installed it with no problem whatsoever. Have order parts from PartSelect before and have been very happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from WOODBURY, MN
- Parts Used:
- 154827601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from KILLEEN, TX
- Parts Used:
- 154388801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer liquid cap was leaking.
I replaced the old cap with the one I ordered from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from MILFORD, MA
- Parts Used:
- 154574401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door broken would not close
1.Turn off electricity. 2. Remove two Phillips screws on either side of front panel 3. Remove front panel 4. Remove 6 screws from the old dispenser 5. Pull both wires connectors from dispenser 6. Remove dispenser 7. Install the new dispenser and reverse the steps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from GREENFIELD, IN
- Parts Used:
- 154388801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Unable to add rinse aid
Screwed in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Niall from Schaumburg, IL
- Parts Used:
- 154574401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay closed
Followed the YouTube video. Replacement fit perfectly , only took 10 minutes to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Carrollton, KY
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle
Simple- Disconnect electric to washer, Remove inner door panel with philips screw driver, disconnect electrical wires watching exactly how they are to be replaced. remove star screws securing handle mechanism. Replace with new handle, connect wiring, replace inner door panel and your all set. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Ozone Park, NY
- Parts Used:
- 154043802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom trim peice was badly twisted and bent.
The dishwasher was already lose so laying on it's back was easy. Two phillip screws were all that held the piece in place .... and the replacement was a simple slide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Pleasant Hill, CA
- Parts Used:
- 5304442175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
plastic door latch handle broke
First I removed the 5 screws holding the dishwasher door control panel. Then removed the 2 screws holding the broken latch. Then removed an electrical contact from the broken latch and installed to the new latch one contact at a time. Reassembled all in reverse order to completion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- erika from deerfield beach, FL
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
latch broke had to open door with a screwdriver
removed screws to loosen front door panel then removed the wire connection, then removed the broken latch with screwdriver, installed new latch in same manner, fastened front panel back with the removed screws and I was back in business, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Whitman, MA
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent door/dispenser would not close,
removed screws holding door panel, turned off electricity,removed old part and installed new dispenser, the dishwasher is back in business. Be sure to use the proper screws when putting back the door panel.The instructions for installation were in the new part assembly.
Thank You for all your help
Pat Johnson
Thank You for all your help
Pat Johnson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Amherst, NY
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch broke and dishwasher could not be opened.
Removed the front cover by unscrewing the 8 screws. Removed the latch and attached new one. Re-attached front cover, and it works fine.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.
Was this instruction helpful to you?
Thank you for voting!