MDB662RBR0 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lin from San Francisco, CA
- Parts Used:
- 5300809611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher leak
At first remove the lower rack to give more room for you to lean over the inside of the dishwasher then remove the old gasket tub 90 inches long make sure that you know which side goes where, so that it will be easy to put the new one. Then press the gasket firmly on the side.Now you can start your dishwasher with no leak and saves you a lot of money for buying a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NORTH BEND, OR
- Parts Used:
- 5304507405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced the side rollers in the dishwasher
Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from commerce, GA
- Parts Used:
- 5300809703, 154103601
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
door would "fall" open
Removed the "kick plate" (4) screws. the hard part was attaching the springs to the door hooks. you cannot see them, have to go by feel. then stretch them to lower frame. attached the lower door trim piece with three screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Arvada, CO
- Parts Used:
- 5300809909
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
heard a noise while dishwasher was in operation, opened door and noticed the dishes were dry, no water was spraying out and dishwasher was making a whirling noise.
After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from Bryan, OH
- Parts Used:
- 5300809611
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The seal in the door was broken.
I had to replace the door gasket but it would not go in very easy..So I put the gasket in a sink of warm water so it would be more pliable. Then it went on fairly easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Charlotte, NC
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heating Element Seal and Nut
Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Wyomissing, PA
- Parts Used:
- 5300809703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher door more difficult to open and close
Removed two screws holding the dishwasher in place under the cabinet. Pulled the dishwasher out to expose the door springs. Removed the old springs and installed the new ones in just a few minutes. Pushed the dishwasher back into the cabinet and replaced the screws. Job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Los Angeles, CA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack got hung up & wouldn't roll
I snapped on the new roller and bingo! problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from East Stroudsburg, PA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken rack rollers
Two rollers on the lower rack were missing and one was flattened. I popped off the bad roller and snapped the three new rollers in place, all by hand. Took about 60 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Longview, WA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken clip would no longer secure wheel
Snapped the new one in. One second repair - like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Upperco, MD
- Parts Used:
- 154106202
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Small Constant Drip (Leak)
I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Riley, MI
- Parts Used:
- 5300809703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
old springs were broken
used the pliers to grip the end of the spring, extended it and removed it from the door and frame. The install then followed. It takes longer to remove the front panel than to do the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from McDonough, GA
- Parts Used:
- 5300809703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken door springs
very simple to do....attach spring to door...stretch to hole in frame and attach there...easy as 123
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- denise from New Lisbon, NJ
- Parts Used:
- 5300809611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water was leaking out of the door
I pulled the old door gasket out, cleaned the guck out and pushed the new one in it's place.
Was this instruction helpful to you?
Thank you for voting!