FDR251RJS0 Frigidaire Dishwasher - Instructions

Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.

shut off the power on the breaker box, 6 screws inside the door on the tolp and side,pulled 4 wires off, 2 star head screws on the unit. took bad unit off,put new one on and put the screws back in.

5 minutes

Removed the screws that held the cover on, then removed the 2 screws that held the door latch in place. Disconnected the broken door latch and attached the new one. Put all the screws back in and that was it! Also, the shipment of the part was SO QUICK!

After watching the repair video, it was 'easy as pie'. I would have thought the gasket was too long and cut it off if not for the video. Thank you. Saved a great deal of money not having to have a repair person do the work. I strongly recommend watching the video.

Removed the screws holding the door panel and as the sheet said was the way the it went. Two screws holding the handle latch and replaced it and put the door back on. There was 4 wires to replace on the latch. Replaced the gasket and the job was done. All in all it was a very good experience with good instructions and very good same day shipping. A VERY GOOD EXPERIENCE.

I replaced this latch,but noticed that the electric terminal configuration was not identical to the old original part. There were no installation instructions furnished for installing this new part, so I had to guess that the wire terminals attached to the new part in a similar position as detached from the old part. So far the renter has not called that the dishwasher is not operating correctly.

Removed six philip head screws to remove upper half of the dishwasher door unit to access handle, then remove handle by remove two star screws and for wires connectors. Installed in reverse.

Note:
I was very impressed on how quick I received the part after it was ordered.

Watched installation video and followed directions. All went smoothly.

Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.

First I removed the 5 screws holding the dishwasher door control panel. Then removed the 2 screws holding the broken latch. Then removed an electrical contact from the broken latch and installed to the new latch one contact at a time. Reassembled all in reverse order to completion.

Received the part quickly and installed it with no problem whatsoever. Have order parts from PartSelect before and have been very happy

First, I located the dishwasher switch in the circuit breaker and turned it off, so as to kill power to the dishwasher - DO NOT PROCEED WITHOUT DOING THIS FIRST. Unscrewed front panel by removing 6 screws on the inside of the door frame. Then pulled 2 white wires on left and 2 black wires on right off of bottom of latch. Then used hex wrench to remove 2 hex screws holding handle and latch to frame. Then reassembled in reverse order as I disassembled. Note that there was a video on the site when I ordered the part, and it demonstrated all the steps; however, when I received the part and went back to the site to review the video again, it was gone. I'm glad I paid close attention the first time I watched it as it was extremely helpful and showed me exactly how to complete the installation.

Before starting I disconnected the dishwasher. First I removed the door cover which then exposed the interior part of the door. I then used a star bit on the screwdriver to remove old latch. I disconnected the four wires to the door making sure that I made a point of which wire was connected to what. I then inserted the new latch and reconnected the wiring. Finally, put on the door panel and screwed in the remaining screws. About 15 minutes total work time.

Removed the front cover by unscrewing the 8 screws. Removed the latch and attached new one. Re-attached front cover, and it works fine.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.

First I removed the control panel and then removed the screw holding the handle. I then pulled the connector wires off and onto the new handle. I then screwed the new panel into place. Easy job, no mess.