SU330NXR1 Frigidaire Dishwasher - Instructions

All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.

I clipped the wheels onto the rack. It couldn't be any easier. then i removed the # 25 torx screw which attached the broken slide wheel to the tub and installed the new wheel with the same torx screw.

At first remove the lower rack to give more room for you to lean over the inside of the dishwasher then remove the old gasket tub 90 inches long make sure that you know which side goes where, so that it will be easy to put the new one. Then press the gasket firmly on the side.Now you can start your dishwasher with no leak and saves you a lot of money for buying a new one.

First, open the dishwasher door and unscrew it from countertop or side of the cabinet. Second, close the dishwasher door and lock it. Thrid, pull entire washer out slowly. Fourth, remove old door spring on both side and replace with new one using needle nose plier. Fifth, unscrew drain hose from under washer and under the sink disposal and replace with new one. Sixth, run washer and ck for leak then push it back under the counter top...done

Removed the service panel below the door (4 hex-head screws), then reached in and took the old broken spring out (right side) and hooked the new one up.

Glad I bought 2 springs - the other one (left side) broke about a week after I fixed the first one! Replaced it the same way. Helps to have small hands - you can't really see where you're putting the springs but can feel where they should go.

I removed the front panel below the door. There are 4 Hex screws, two at the top (accessible with the door open) and two at the bottom. After removing the screws, the panel came off, and I could reach inside to replace the springs. I found it easier to use a socket wrench than a screw driver.
Easily done. Anybody can do it. It took longer to clean up the panel than to do the actual repair.

very simple to do....attach spring to door...stretch to hole in frame and attach there...easy as 123

In about 20 minutes, I was able to remove the front panel and access the springs. Besides a hard water line in the way, it was a snap.

After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.

I had to replace the door gasket but it would not go in very easy..So I put the gasket in a sink of warm water so it would be more pliable. Then it went on fairly easy.

Removed two screws holding the dishwasher in place under the cabinet. Pulled the dishwasher out to expose the door springs. Removed the old springs and installed the new ones in just a few minutes. Pushed the dishwasher back into the cabinet and replaced the screws. Job done.

I snapped on the new roller and bingo! problem solved.

Two rollers on the lower rack were missing and one was flattened. I popped off the bad roller and snapped the three new rollers in place, all by hand. Took about 60 seconds.

I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!

So easy it shouldn't even count as a repair, really. The dishwasher, there when I bought the place, had a lower rack that wouldn't roll out as it should. That's because there were no wheels on the left side.

The rack lifts out easily. These wheels snap on to small protrusions from the wire rack.