CDBEH351US0A Frigidaire Dishwasher - Instructions

The hose goes from the water inlet solinoid to the side of the dishwasher.Remove the kick plate from the bottom front of the dishwasher. Disconnect the water supply to the inlet of the solinoid valve (copper tubing on mine). Remove the screws under the counter top which hold the dishwasher in place. slide the dishwasher out from under the cabinet only as far as needed to expose the hose(about 1 foot). The hose is behind the insulation. Remove the hose clamps from both ends of the hose(solinoid outlet and side of dishwasher)Remove hose carefully because this is all plastic. Install replacement hose and clamps. The new hose is several inches too short and will not fit into the upper hose guide, just bend it underneath. Be sure to put hose in lower keeper on side of dishwasher. Attach clamps, tape insulation back in place, slide dishwasher back under counter and install screws under counter. Attach copper tubing to water inlet solinoid valve. Run dishwasher and check for leaks. Replace kick plate. Note: I had enough loose electrical wire to slide my dishwasher out. If you don't have enough wire to slide out the dishwasher you should call a repair man.

I removed the 2 screws that hold the dishwasher in place. Slide out the unit just far enough to access the brass nuts on the heating element. Pulled off the wire, and replaced the broken nut with the new nut. Replaced the wire, slide the unit back into place and reattached the 2 under counter screws. Done!!!

I already had the dishwasher removed for remodeling. I wrecked the drain hose myself. When I received the replacement it was a breeze to install.

I just pulled the old one out and installed the new.

Wrap your pliers in some kind of padding so you don't damage the plastic. Spin the base ( not the spinner itself) which is left-threaded(normal). If the gasket doesn't fall out (mine did) pull it out gently. Clean the gasket socket with a rough cloth or scotch-brite pad and install the new one. Put it all back together and wash dishes, man.

replaced gasket easy-peesy

Purchased new drain pump thinking that was the issue. When I was installing I noticed the drain hose was clogged. Since the way out cabinets were installed by the previous owner getting the dishwasher out is a little more complex so installed the drain pump and drain hose just to make sure. Runs like new!

There was an excellent "how to" video on the internet which also pointed me to the part I needed. I did not even remove the dishwasher as recommended. I removed the lower kick plate, removed the power connector at the leaking input, removed the bad nut and installed the new nut.

After watching the video the replacement went very easy. The only thing I would suggest is that you replace both springs to equalize the tension.

First, I unplugged the dishwasher. After removing the under counter mounting screws, I pulled the dishwasher out from the cabinets. Because the switch is hard to reach, I put the dishwasher on its side (very carefully). Make sure to drain the dishwasher first, or it will leak all over your kitchen. To remove the switch, I unscrewed the single black screw in the middle of the switch and unplugged the electrical wires. I put the new switch in its place, screwed in the screw, and plugged in the electrical connection. I set the dishwasher upright, and ran it through a cycle before reinstalling it into the cabinet. I had previously tried replacing the water inlet valve, but that was not the problem.

The left-side dishwasher door spring snapped. The door was then noticeably heavy to open and close. To investigate the problem, I shut off the circuit breaker and the water feed. I removed the two screws that secure the top of the dishwasher to the counter, so I could pull out the unit and see the door springs. (TIP: remove the bottom metal panel as well to see if you have a flexible or rigid pipe for hot water. If you have a rigid pipe like I do you might want to be careful pulling the unit forward.) With the unit pulled forward I could see the snapped spring; it had actually shot up and was wedged between the unit and the cabinet. To to the repair, I attached the new spring to the door first. Then I closed the door so the spring was slack and used pliers to attach it to the bottom of the unit. (To access the bottom of the unit, you need to remove the metal panel at the bottom, as mentioned above.) I used the other spring as a comparison as to where to attach.

Ordered the new roller assembly and in no time the upper rack was back together, up and running. Now to see about replacing the other two rollers and the side rails as they are showing wear and tear.

Thanks for the quick ship.

replacing spring is easy.but you have to disconect the water line to slide the washer out to get at the spring.service was exelant. part was deliverd next day.

removed all strainer and filter parts and soaked them in lime remover for several hours until clean. then,I rein stalled all the parts including the new filter screen.