CDBEH351US0A Frigidaire Dishwasher - Instructions

Pulled off the old gasket and replaced it the same way with the new one.

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.

My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.

used pliers to hook up spring according to repair video.5 mins to check for proper tension.

Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.

The first sensible thing to do is to find the circuit breaker for your dishwasher and switch it off so as not to short anything (or yourself) out. Next, remove the lower piece of metal bracket from beneath the door by unfastening the two sheet metal screws (a nut driver or a screwdriver will do the job), taking note as to how it comes off so as to facilitate replacement. Some will recommend loosening the screws at the top from beneath the counter and pulling the machine forward a bit to gain access to the sides but, if you have a small enough hand (as I do), you can just reach in there and and hook the spring into place. I didn't want to risk loosening any plumbing! You'll need a flashlight to see where the ends connect. And, if one spring is still intact, you can reference that to reassure yourself you've got it right. I was able to stretch the spring out by hand and hook the thing to that little plastic gadget that pivots when you open the door. That's it! Button her up! You're done!

Removed the cover at the front bottom to gain access to the nuts holding on the element.
Turned off dishwasher breaker.
Removed the wires connected to the element.
With a 1/2" wrench, removed the element mounting screws.
Removed the bottom rack.
Removed the lower spray arm.
Removed the element from 2 clips.
Removed the element.
Put the new element in place.
Clipped it in.
Put new screws on and tightened up with a wrench. Not too much but enough to squash the washers to make a tight seal.
Replaced wires.
Replaced spray arm and bottom rack.
Turned on the breaker.
Ran it through a cycle to check for leaks.
Replaced bottom cover.

After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!

Eventually broke off old heating element to get it out

I watched the video on the website on how to remove the top rack, and installed the new wheel and bushing. Simplest fix I ever did.

First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.