FDB101SAW0 Frigidaire Dishwasher - Instructions

Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.

Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.

New right away when we heard the sound, the spring broke. Easy to replace, pull dishwasher out from under countertop, usually held in place by two screws into countertop. Remove screws, pull out dishwasher. Close door, springs will now have the most slack in them. One spring located on each side. Remove spring from one side and replace with new spring to ensure proper spring placement. No actual tools needed as spring rests on a bracket attached to door and other end of spring goes through hole in bottom of dishwasher rack. open door to test for tension as there are several holes to choose from. .

#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.

Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.

Both the door latch assembly and strike broke on the dishwasher. I was happy to find both parts available at PartSelect.com. Simply removed mounting screws so I could pull the dishwasher out, removed the old strike, disconnected the 4 wire attachments and removed the ddor latch assembly, and re-assembled with the new parts. Pretty easy job- the only unusual thing was that you need a torx screwdriver for the latch assembly.

After receiving my part in a timely manner, I removed the six screws holding the cover on the door. After making sure the appliance was unplugged, I removed the two star screws and removed the broken latch assembly. I disconnected the four electrical wires noting their placement. I connected the wires to the new latch assembly, screwed the assembly to the door, and replaced the cover on the door. That was one of the best quick-fix experiences I have ever had. Thanks PartSelect.com!!!!

I removed the screws on the inside of the dishwasher door to remove the front facade to get access to the door latch assembly, I think about 6 screws. Then I unscrewed the two hex screws that mounted the latch assembly to the door. I then had to un-hook the electrical wires (4 plugs, 2 on a side) from the assembly. I attached those same plugs to the new door latch, and mounted the assembly back on with the two screws, and tested the door to see if it closed, latched, and if the dish washer would run (since I unhooked and rehooked up the electrical wires). Finally I screwed the front facade back on and was done. It took about 5 minutes. I did get a small shock when I was removing the electrical plugs from the old assembly from touching the metal dish washer door and one of the plugs at same time.

I removed the screws from the inside of the door. There are also tiny screws you have to remove that holds the part onto the door. Then I was able to remove the part, unplug the power receptacles and install the new part. Very simple!!

I removed 6 screws to get to the door latch, then removed 2 screws to remove the broken latch assembly. Changed out 4 wires, reinstalled the 2 screws that attached the latch to the door,thenreinstall the 6 screws that assemble the door back together. Everything fit and works properly. Thanks guys, your service was great.