DW5200A1 Frigidaire Dishwasher - Instructions

Removed the service panel below the door (4 hex-head screws), then reached in and took the old broken spring out (right side) and hooked the new one up.

Glad I bought 2 springs - the other one (left side) broke about a week after I fixed the first one! Replaced it the same way. Helps to have small hands - you can't really see where you're putting the springs but can feel where they should go.

After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.

I had to replace the door gasket but it would not go in very easy..So I put the gasket in a sink of warm water so it would be more pliable. Then it went on fairly easy.

I removed two screws that hold unit to countertop,
just pulled out unit about two inches. Removed broken door springs. Installed new door springs and pushed unit back into place and installed the 2 countertop screws DONE.

In about 20 minutes, I was able to remove the front panel and access the springs. Besides a hard water line in the way, it was a snap.

Removed two screws holding the dishwasher in place under the cabinet. Pulled the dishwasher out to expose the door springs. Removed the old springs and installed the new ones in just a few minutes. Pushed the dishwasher back into the cabinet and replaced the screws. Job done.

Two rollers on the lower rack were missing and one was flattened. I popped off the bad roller and snapped the three new rollers in place, all by hand. Took about 60 seconds.

So easy it shouldn't even count as a repair, really. The dishwasher, there when I bought the place, had a lower rack that wouldn't roll out as it should. That's because there were no wheels on the left side.

The rack lifts out easily. These wheels snap on to small protrusions from the wire rack.

The parts arrived 20 hours after ordering -great service & the parts were just like like the removed parts only new. The old door gasket was pulled from its groove & and the new gasket was installed witout using tools. No more leaking water.The door spring installation wesa bit more difficult. The front bottom was removed with a nut drive, the broken springs were fished out, new springs were pull onto the arms and the cover put back in place. Not a bad job for a crippled, one-eyed 82 year old man.

Fisrt, I opened dishwasher door. I then pulled out the lower rack & put new part in place and pushed in lower rack. Last, I closed dishwasher door.

Installed New rollers onto bottom rack. Part order & delivery were top notch from Partselect. Will definitely order from them again.

merely snapped the part on

Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.

This could not have gone easier! As long as you get the proper parts it's a piece of cake. I wish everything was this easy!

I ordered a new door gasket and door spring. I unscrewed the two screws that hold the dishwasher in place and pulled it out. I pulled the old broken spring off with pliers and installed the new one ,,,very easy. I then took the new door gasket and soaked it in hot water in the sink for 15 min. That made it very soft and pliable to work with. I used pliers to pull the old gasket out then cleaned the area around the old gasket where crud had built up. I pushed in the new gasket working from top to bottom one side at a time. Turned it on an ran through a cycle and it works perfect now ,,,no leaks.