GDPH4515AF1B Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from TIOGA, WV
- Parts Used:
- 5304525218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Latch was bad
Just take the door apart remove the latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from OXFORD, MS
- Parts Used:
- 154106202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water was leaking through the heating element Accra point.
Isolated the leak and found the nut had split thereby allowing a loose seal and water penetration. Ordered 2 nuts just in case the other goes and the installation was easy. Unplug the unit, remove baseplate, remove screws under the countertop, and slide the unit out a bit. Use needlenode pliers to remove terminal connection and replaced nut. Reverse it for assembly. 3 minutes tops $6 later it is done. Easy money saved by a DIY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pietro from BOSTON, MA
- Parts Used:
- 5304535768
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack wasn't operating properly. The wheels had broken off.
Ordered lower dish rack, which arrived fully assembled and ahead of schedule, and put it in the dish washer. Took 5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from MILTON, MA
- Parts Used:
- 154579101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stretched out spring
Inserted springs into corresponding holes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from EVERETT, WA
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Heating Element was corroded.
It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from STILWELL, OK
- Parts Used:
- 5304507087
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Wouldn't fix it
The part wasn't correct and I have to pay postage back which is nearly as much as the part so it's stupid for me to spend more money on a part that want work I want order from your store again.
Was this instruction helpful to you?
Thank you for voting!
Plastic had melted on the screw
Eventually broke off old heating element to get it out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from W HEMPSTEAD, NY
- Parts Used:
- 5304507087
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Leaking
Had to shut electricity off and turn water off and disconnect them both. Take the screws out from underneath the counter. Slide out the unit disconnect the filler tube in the back disconnect the hose and replace and repeat the process to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from hull, MA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Spray Arm Did not Turn
The bottom spray arm would not turn or fall off the stem assembly, so the dishes would not come clean like usual. The spray arm connects to the stem assembly via two plastic prongs that secure the spray arm. I removed the spray arm from the socket (no tool required) and observed the prongs had worn completely away. I grabbed the power screw driver and removed the assembly (3 screws). I placed the new assembly in place, secured the screws, and attached the spray arm. Finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Racquel from Lake Charles, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing roller made it difficult to move rack.
The new roller just snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette from Fort Lauderdale, FL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from ROANOKE, VA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part was damaged and dishes weren't clean
Removed 3 screws, swapped parts - done. Wonderful feeling and saved a service call. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from San Marino, CA
- Parts Used:
- 5304535768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack badly rusted
Best part delivery ever! Ordered Saturday after Thanksgiving when bottom rack of dishwasher just was overused and beyond repair - part shipped Monday and was here Tuesday! Only hand washed dishes for three days. No complaints at all! Took the old rack out and slid the new one in! Best deal of the year!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!