GDPP4517AF1B Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from EAST ISLIP, NY
- Parts Used:
- 5304532950
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A piece of the upper rack began to rust out
Used the screwdriver to pry the upper rack left side tine up and out. Slipped the new one into place and pressed hard to seat the tine. this process took all of about 20 seconds to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette from Fort Lauderdale, FL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Clinton, OH
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking tub seal
Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from WOODBURY, MN
- Parts Used:
- 154827601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SUNBURY, PA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Left door spring had stretched and no l held the door upright
Opened the package and inspected the new spring
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul J from LEXINGTON, MA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One door spring was broken - the other was spring.
Instead of moving the unit out from under the counter, I did the job with the unit in place: (1) long reach to remove the old springs and attach the new ones to the frame at back of the unit, (2) use a loop of string to hook onto the other end of the spring, stretch it a little, and keep it stretched by hooking the other end of the loop to the screw that adjusts the unit's height, (3) slip the end of the cable to the front end of the spring and check to make sure that the cable is on its pulley, (4) take the string off the adjusting screw and wiggle it to free it from the end of the spring. (For comfort, lie down on a yoga mat when you do this job - thanks to my wife for this helpful suggestion!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Sublimity, OR
- Parts Used:
- 154756401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cable was broke
Opened door. Located 2 Phillips head screw s attaching the dishwasher to counter and removed them. Slid the dishwasher out about 8 inches. Love broken cable and removed . Inspect spring and attached new cable. Inspected opposite cable and spring. Tucked insulation around dishwasher and slid back into place. Reattached 2 Phillip screws and closed door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from MEDANALES, NM
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Sprang a Huge Leak
I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from COMSTOCK PARK, MI
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
My heating element was cracked
Remover the cracked heating element with the new heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from N ROYALTON, OH
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
The heating element (ring) showed signs of wear
I followed the steps on YouTube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert & Kathleen from FAIRFAX, VT
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door springs were stretched; with one broken
Followed the on-line tutorial. BINGO!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from East Stroudsburg, PA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken rack rollers
Two rollers on the lower rack were missing and one was flattened. I popped off the bad roller and snapped the three new rollers in place, all by hand. Took about 60 seconds.
Was this instruction helpful to you?
Thank you for voting!