FGIP2468UF3A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Todd from Brandon, SD
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper spray arm kept falling off
This part fixed problem. The original part seemed to have a defect. Was simple to fix, simply took off old piece still connected and hand tighten the new piece on, it took about 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Monroe, GA
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper arm fell off frequently
Unscrewed the mounting nut and the assembly came off . A simple task of taking the new assembly and screwing it back on .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Massapequa Park, NY
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The part would constantly fall after every dishwasher run
Removed the old spray arm by unscrewing it from the top inside of the dishwasher. Then screwed on the new spray arm. Could not have been any easier and it has not fallen off since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SUNBURY, PA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Left door spring had stretched and no l held the door upright
Opened the package and inspected the new spring
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert & Kathleen from FAIRFAX, VT
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door springs were stretched; with one broken
Followed the on-line tutorial. BINGO!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from WOODBURY, MN
- Parts Used:
- 154827601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from ELK GROVE, CA
- Parts Used:
- 5304506521
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Plug for soap dispenser.
My future son in law did it. Looked at instructions on the app for the part. Didn't take very long.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul J from LEXINGTON, MA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One door spring was broken - the other was spring.
Instead of moving the unit out from under the counter, I did the job with the unit in place: (1) long reach to remove the old springs and attach the new ones to the frame at back of the unit, (2) use a loop of string to hook onto the other end of the spring, stretch it a little, and keep it stretched by hooking the other end of the loop to the screw that adjusts the unit's height, (3) slip the end of the cable to the front end of the spring and check to make sure that the cable is on its pulley, (4) take the string off the adjusting screw and wiggle it to free it from the end of the spring. (For comfort, lie down on a yoga mat when you do this job - thanks to my wife for this helpful suggestion!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from N ROYALTON, OH
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
The heating element (ring) showed signs of wear
I followed the steps on YouTube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GENE from BRONX, NY
- Parts Used:
- 5304506521
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dispenser failed to operate
Uncomplicated repair. Remove door, remove old dispenser, install new dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from COMSTOCK PARK, MI
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
My heating element was cracked
Remover the cracked heating element with the new heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Clinton, OH
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking tub seal
Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from MURRELLS INLT, SC
- Parts Used:
- 5304506516
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
spray arm on top broke
Just unscrewed the old one and screwed in the new one. Working great! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from PATTON, MO
- Parts Used:
- 5304506516
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Spray arm fell off during cycle
Unscrew old one and put new one in. Only issue we had was the new nut that screws the arm into place did not fit our machine. We had to take the old one off and use it instead.
Was this instruction helpful to you?
Thank you for voting!