LFID2426TF6A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeanette from Fort Lauderdale, FL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from ROANOKE, VA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part was damaged and dishes weren't clean
Removed 3 screws, swapped parts - done. Wonderful feeling and saved a service call. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from hull, MA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Spray Arm Did not Turn
The bottom spray arm would not turn or fall off the stem assembly, so the dishes would not come clean like usual. The spray arm connects to the stem assembly via two plastic prongs that secure the spray arm. I removed the spray arm from the socket (no tool required) and observed the prongs had worn completely away. I grabbed the power screw driver and removed the assembly (3 screws). I placed the new assembly in place, secured the screws, and attached the spray arm. Finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Racquel from Lake Charles, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing roller made it difficult to move rack.
The new roller just snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Killeen, TX
- Parts Used:
- 5304535768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rust overtook the mechanism.
Lifted out the old unit and replaced it with the new one. First one the rollers were bent and wouldn't roll. Replacement unit was supplied for a small additional fee.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Clinton, OH
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking tub seal
Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from Grass Range, MT
- Parts Used:
- 5304507158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The top part of the lower spray arm got stuck on something a broke off the lower part of spray arm.
The are 2 tabs on the bottom of the lower spray arm that I pushed in and the arm popped right off. All you have to do is push the new spray arm on until you hear it snap into place, and you are done. It is really easy to do, and the part fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from WOONSOCKET, RI
- Parts Used:
- 5304519906
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My dishwasher wasnt washing the dishes.
I had to remove the dishwasher and lay it on its back. But after that I swapped out the pump, put it all back together, and I was good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Sublimity, OR
- Parts Used:
- 154756401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cable was broke
Opened door. Located 2 Phillips head screw s attaching the dishwasher to counter and removed them. Slid the dishwasher out about 8 inches. Love broken cable and removed . Inspect spring and attached new cable. Inspected opposite cable and spring. Tucked insulation around dishwasher and slid back into place. Reattached 2 Phillip screws and closed door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Fort Myers, FL
- Parts Used:
- 5304535768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced lower rack
Just replaced the rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from FAIRPORT, NY
- Parts Used:
- 5304507158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The spray arm on the lower level had broken
Easy repair .part was perfect. Did have to you tube video to make sure I was doing it correctly. Instructions with part would be helpful.Part arrived quickly without issue!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dante from SOUTHOLD, NY
- Parts Used:
- 5304535768
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rusted rack
open door pull out old rack replace with new rack !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!