804621672A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matthew from west river, MD
- Parts Used:
- 5304517203
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Dishwsher leaking
Thought the problem was a faulty door gasket (there was a gap in the middle of it) so I ordered new(new one had a gap also) replaced it anyway - maybe it was worn out? Still leaked! Had to sit and stare at it and cycle it through. finally realized the spray arm had a hole in the end that was spraying directly into the gap in the door gasket. Hot glued the hole and it stopped so I bought a new spray arm - no leaky!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Winder, GA
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spray arm came off and melted to heating element
I first removed the bottom rack and took out the spray arm (which was now in two pieces) I took some steel wool and scrubbed off the melted residue from the old arm. I took the new spray arm out of the plastic and clipped it into the bottom of the dishwasher. It spun around great and so I put the bottom rack back in and told my wife to try to run a load of dishes throu. It ran great, dishes got clean...easy fx!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from hull, MA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Spray Arm Did not Turn
The bottom spray arm would not turn or fall off the stem assembly, so the dishes would not come clean like usual. The spray arm connects to the stem assembly via two plastic prongs that secure the spray arm. I removed the spray arm from the socket (no tool required) and observed the prongs had worn completely away. I grabbed the power screw driver and removed the assembly (3 screws). I placed the new assembly in place, secured the screws, and attached the spray arm. Finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from WILMINGTON, IL
- Parts Used:
- 5304517203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Became loose, and spray arm burned alittle. Stopped working and water started over flowing.
Unscrewed the old arm, and watched a utube video to place back in properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from FT LAUDERDALE, FL
- Parts Used:
- 5304500204
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water leak
watched a video, really easy fix. Solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from MARINE ST CRX, MN
- Parts Used:
- 5304532199
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaked spot free fluid
Replaced part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from NUNNELLY, TN
- Parts Used:
- 5304517203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Sprayer arm design in newer model was not sufficiently cleaning
Pulled the completely empty bottom rack out, popped the old spray arm off, popped the new one on, and replaced the basket. Easy peasy. One of the easiest repairs possible IF it fixes the problem. (We had an older model Fridgaire dishwasher with this type spray arm versus the one that came in the new one and it worked great for 12 years. Falling back to it in a fashion was a logical attempt at a solution)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from WOODBURY, MN
- Parts Used:
- 8581548276014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hank from Fort Pierce, FL
- Parts Used:
- 5304532199, 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Making noise during operation.
Checked your videos and found the lower spray arm damaged (nubs worn down). Previous owner had some work done and didn't reinstall the parts properly. While during the repair, I also decided to replace the Detergent Dispenser and make a new spray shield. I guess the previous owner decided one wasn't needed.
Easy install, no noise.
Capt. Hank
Easy install, no noise.
Capt. Hank
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from MEDANALES, NM
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Sprang a Huge Leak
I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from COMSTOCK PARK, MI
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
My heating element was cracked
Remover the cracked heating element with the new heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from N ROYALTON, OH
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
The heating element (ring) showed signs of wear
I followed the steps on YouTube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlene from Houston, TX
- Parts Used:
- 154430501
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Door Spring
First remove the kick plate.
Then look with a flashlight & mirror to make sure which, the spring and or the Spring Linkage are broken.
With the door open, to have less tension on the spring, replace the spring and or the spring linkage.
Attach the kick plate
Then look with a flashlight & mirror to make sure which, the spring and or the Spring Linkage are broken.
With the door open, to have less tension on the spring, replace the spring and or the spring linkage.
Attach the kick plate
Was this instruction helpful to you?
Thank you for voting!