GDPP4517AD0A Frigidaire Dishwasher - Instructions

After reading some "Suggested Installation Instructions" on the Parts Select Website, I felt at ease tackling this job. After opening the door, I simply pulled-out the existing door gasket. The installation involved simply pressing in the new gasket with my finger and insuring it was properly seated. The only tool I had to use was a pair of scissors to cut the excess length as I pressed it in. REALLY APPRECIATED THE SIMPLE INSTALLATION INSTRUCTIONS as I had never done this particular task.

Pulled out the gasket,trimmed the gasket to fit and alittle pressure to put.it in place, very easyto do. No worries any one can do this and savek yourself costly repair person.

removed old hose by loosening clamps replaced hose reclamped

Very helpful and was amazed how quickly it was delivered. Very pleased.

There was an excellent "how to" video on the internet which also pointed me to the part I needed. I did not even remove the dishwasher as recommended. I removed the lower kick plate, removed the power connector at the leaking input, removed the bad nut and installed the new nut.

Open door, remove 2 screws from underside of countertop. Close door, remove screws from bottom kick panel,( 2 piece, set aside). Slide dishwasher out, to gain access to left side. (disconnect water line, drain line, and power, if not enough slack). Carefully remove 2 wire clips from discharge pump (located directly behind main motor). Remove screws (3) from pump housing. carefully pull out old pump. Check and clean pump mounting area. Push new pump into opening, do not force. turn to line up screw holes, insert screws, and tighten. install wire clips as removed ( white on left) . If needed, reinstall water line, drain line, and power. Slide dishwasher back into opening. Run a rinse cycle, and check for leaks. If good, install screws into countertop, and install kick panel.

After looking at several youtube.com remedies, I zeroed in on the problem... non-functioning waste water pump. I also noted that the valve flapper was in rough shape so ordered both. Once I got the new parts, I replaced the old ones in less than 30 minutes. When I removed the old pump assembly, I discovered that the four-blade waste water wheel had broken off. For about $75, I repaired what no one in my small rural town could. I think the retail on the dishwasher was somewhere between $300-350, so I figured it was a good deal. Also I scored BIG man points with my wife!

Looked up the code on the internet and it said it was the vent fan, was easy to pull out and replace. Saved hundreds

All I have to say is paets select is the best company I have delt with in the last 20 years

The hose goes from the water inlet solinoid to the side of the dishwasher.Remove the kick plate from the bottom front of the dishwasher. Disconnect the water supply to the inlet of the solinoid valve (copper tubing on mine). Remove the screws under the counter top which hold the dishwasher in place. slide the dishwasher out from under the cabinet only as far as needed to expose the hose(about 1 foot). The hose is behind the insulation. Remove the hose clamps from both ends of the hose(solinoid outlet and side of dishwasher)Remove hose carefully because this is all plastic. Install replacement hose and clamps. The new hose is several inches too short and will not fit into the upper hose guide, just bend it underneath. Be sure to put hose in lower keeper on side of dishwasher. Attach clamps, tape insulation back in place, slide dishwasher back under counter and install screws under counter. Attach copper tubing to water inlet solinoid valve. Run dishwasher and check for leaks. Replace kick plate. Note: I had enough loose electrical wire to slide my dishwasher out. If you don't have enough wire to slide out the dishwasher you should call a repair man.

Disconnect drain hose, disconnected power, laid dishwasher on its back. Had to remove wash motor, then had access to the drain pump. Removed bad drain pump, installed new drain pump, reinstalled wash motor, reconnected drain hose, then reconnected power. Job is done working as intended. Really easy.

I already had the dishwasher removed for remodeling. I wrecked the drain hose myself. When I received the replacement it was a breeze to install.

I removed the 2 screws that hold the dishwasher in place. Slide out the unit just far enough to access the brass nuts on the heating element. Pulled off the wire, and replaced the broken nut with the new nut. Replaced the wire, slide the unit back into place and reattached the 2 under counter screws. Done!!!

pULLED THE WASHER FROM THE COUNTER disconjnected the house from the garbage disposal connected thenew hose to the disposal, remove other end of old hose from thedishwasher and replace with the new drainage hose.

Removed old gasket,placed new one on pressing into place.Very quick and easy.Saw the youtube on how to do it.Unfortunately this was not the problem.now have a new dishwasher same brand.