GDPH4515AD0A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Theo. J. from Green Bay, WI
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken part that holds bottom spray arm on.
This was great! Removed 3 screws, took out old broken part, set in new part and screwed tight! 1 2 3 and done. Very Fast shipping less than 24 hrs.. WIFE IS HAPPY. Ted W.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Fort Huachuca, AZ
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stem assembly was broken.
I removed the three screws that held the stem assembly in place, removed the old stem assembly and replaced it with the new one. Replaced the screws and began using the dishwasher again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelley from LACONA, NY
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Dishwasher hose had hole in it. It was 23 years old.
After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!
Was this instruction helpful to you?
Thank you for voting!
the nut holding on the element would not tighten. leaked at the location where the nut was located
Removed the cover at the front bottom to gain access to the nuts holding on the element.
Turned off dishwasher breaker.
Removed the wires connected to the element.
With a 1/2" wrench, removed the element mounting screws.
Removed the bottom rack.
Removed the lower spray arm.
Removed the element from 2 clips.
Removed the element.
Put the new element in place.
Clipped it in.
Put new screws on and tightened up with a wrench. Not too much but enough to squash the washers to make a tight seal.
Replaced wires.
Replaced spray arm and bottom rack.
Turned on the breaker.
Ran it through a cycle to check for leaks.
Replaced bottom cover.
Turned off dishwasher breaker.
Removed the wires connected to the element.
With a 1/2" wrench, removed the element mounting screws.
Removed the bottom rack.
Removed the lower spray arm.
Removed the element from 2 clips.
Removed the element.
Put the new element in place.
Clipped it in.
Put new screws on and tightened up with a wrench. Not too much but enough to squash the washers to make a tight seal.
Replaced wires.
Replaced spray arm and bottom rack.
Turned on the breaker.
Ran it through a cycle to check for leaks.
Replaced bottom cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from PORT ORCHARD, WA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Brass nut split down its side , why ???????
Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from W HEMPSTEAD, NY
- Parts Used:
- 5304507087
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Leaking
Had to shut electricity off and turn water off and disconnect them both. Take the screws out from underneath the counter. Slide out the unit disconnect the filler tube in the back disconnect the hose and replace and repeat the process to put it back together.
Was this instruction helpful to you?
Thank you for voting!
Plastic had melted on the screw
Eventually broke off old heating element to get it out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from EVERETT, WA
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Heating Element was corroded.
It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Attleboro, MA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dishwasher leaking water on my hardwood floor
I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!
Greg
I also scored big points with the wife on my handyman repair! Thanks Partselect!
Greg
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from ROANOKE, VA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part was damaged and dishes weren't clean
Removed 3 screws, swapped parts - done. Wonderful feeling and saved a service call. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from hull, MA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Spray Arm Did not Turn
The bottom spray arm would not turn or fall off the stem assembly, so the dishes would not come clean like usual. The spray arm connects to the stem assembly via two plastic prongs that secure the spray arm. I removed the spray arm from the socket (no tool required) and observed the prongs had worn completely away. I grabbed the power screw driver and removed the assembly (3 screws). I placed the new assembly in place, secured the screws, and attached the spray arm. Finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Clinton, OH
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking tub seal
Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from WOODBURY, MN
- Parts Used:
- 154827601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SUNBURY, PA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Left door spring had stretched and no l held the door upright
Opened the package and inspected the new spring
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!
Was this instruction helpful to you?
Thank you for voting!