FGID2468UD2A Frigidaire Dishwasher - Instructions

After shutting off power to the dishwasher, I removed the two screws holding the door cover on the inside of the door sides, about 8 inches from the bottom of the door. I slid the cover down and off, and unplugged the wires to the dispenser. Then I removed the six screws holding the dispenser in place, removed the old dispenser, installed the new one, replaced the six screws and plugged the wires back in. The door cover and the two screws was all that was left. It took about ten minutes. Easy.

Disconnected power, water, and drain tube from dishwasher. Pulled dishwasher out and laid it on right side. It was not necessary to remove the pump motor. When disconnecting the water line, it is better to remove 3/8 line from the appliance adapter rather that the appliance adapter from the dishwasher as the nylon connection tends to strip.

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.

Your service was great, the basket came in two parts and all I had to do was put the two together and put it in the dishwasher. I am glad we were able to get a new one. Thanks again for such quick service. Thank you very much for such great service.

Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.

I read the instructions that others had posted and completed the repair in less than 5 minutes!

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

Arm screwed on and immediately fixed the problem.

Open door, Lift out old ,replace with new.

Still have a slight leak, but I'm thinking it may just need time to seat itself.

My husband and dad actually did the repair, but my husband not being a handy guy said it was, 'so easy, anyone could do it!' He was very nervous about taking on the project, the longest part was testing to make sure it worked(running a cycle).
The simply pulled out the dishwasher, after disconnecting all electrical power, drained the rest of the water that we couldn't see from above, following the video given took out the old part without needing to take out the motor and were able to replace the drain pump, put everything back together besides sliding it into place in case it didn't work, in less than 15 minutes! When the short cycle finished and the water had drained they put it back into place and ran an energy saver cycle and it worked like a charm! Since then(2 weeks ago) we have now ran every function and have had no issues! Every time we open the dishwasher we comment on how much we missed having a dishwasher! Haha!

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

I removed the access panel using a nut driver. One fastener on each side at the lower front panel. Move the two piece lower panel and set aside. Locate the broken spring. It will be on the floor under the dish washer. Remove the broken spring. Place the new spring end in the hole in the chord end and place the chord over the plastic guide. Use a pliers to stretch the spring and fasten it to the hole in the lower dishwasher frame at the back of the dishwasher. Check the door for proper tension. Replace the lower panel and secure with the two screws. I recommend replacing both springs at the same time to insure proper balance. If you only replace one spring you will be replacing the other in the near future.

Simply took the old one out, and put the new one in.