FGID2468UD1A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from Milford, MA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish washer leaking at the door
Pulled off the old gasket and replaced it the same way with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from STURBRIDGE, MA
- Parts Used:
- 5304532969
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Parts rusting
Open door, Lift out old ,replace with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SUNBURY, PA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
the end on one of the door springs on the dishwasher broke off
I removed the access panel using a nut driver. One fastener on each side at the lower front panel. Move the two piece lower panel and set aside. Locate the broken spring. It will be on the floor under the dish washer. Remove the broken spring. Place the new spring end in the hole in the chord end and place the chord over the plastic guide. Use a pliers to stretch the spring and fasten it to the hole in the lower dishwasher frame at the back of the dishwasher. Check the door for proper tension. Replace the lower panel and secure with the two screws. I recommend replacing both springs at the same time to insure proper balance. If you only replace one spring you will be replacing the other in the near future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert C from COTTONWOOD, AZ
- Parts Used:
- 5304535382
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old basket developed holes and needed replacing.
Took the old out and placed the new in its place. That simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from STILESVILLE, IN
- Parts Used:
- 5304523304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad code OU came on screen
Pull out shut off power unscrewed fan.Replaced with new fan . Rest power and shoved back in ran cycle. All was fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from MATAWAN, NJ
- Parts Used:
- 5304520552
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The display panel was flashing ERR
I replaced the 2 circuit boards located under control panel, plug and play, simple repair, the hardest part was get the front panel back on , just line up the screws and your good to go NO NEED TO REMOVE ENTIRE DOOR.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FAIRHAVEN, MA
- Parts Used:
- 5304525218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door wasn’t locking
You tube video and it was so easy less than 20min had it fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex from COMMERCE, GA
- Parts Used:
- 5304500204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom door seal leaking on my dishwasher
Still have a slight leak, but I'm thinking it may just need time to seat itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERTA from FAIRBANKS, AK
- Parts Used:
- 5304532229
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
wheels break or bend or fall off
if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from Hastings, MI
- Parts Used:
- 5304525218
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher latch
Removed screws for door panel, then literally 2 screws to change out the latch!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SHELBYVILLE, IL
- Parts Used:
- 5304517890
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom sprayer came off and fell on heat bar and melted in two pieces
removed bottom spray bar snapped new orbital sprayer onto bar then reinstalled spray bar
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from Keota, OK
- Parts Used:
- 5304525218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water did not drain. Found the door latch broken
Unplug dishwasher. Open the door. Remove two Phillips head screws holding the door panel on. Slide door panel down and out to remove. With door still open, remove the six T20 torque screws that hold the control panel. Behind the control is the latch assembly. Take a picture of the wires going into the latch assembly for installation reference(mine was black wires on left and white wires on right). Unplug the two sets of wires. Remove two T20 torque screws that hold the latch. Replace with new latch and reverse steps for installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- elner from new concord, KY
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic piece that held the arm on was worn & dishwasher only 2 yrs old.
Arm screwed on and immediately fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reynaldo from ORANGE PARK, FL
- Parts Used:
- 5304500204, 154827601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leak
Removed all sealer and install new one as instructed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MARSHALL, MI
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
Water inlet tube had worn a hole in it
Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.
Was this instruction helpful to you?
Thank you for voting!