FGIP2468UD1A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Perry from Waynesboro, VA
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper spray arm kept blowing off
Easiest repair ever. The spray arm itself usually really is not the problem, it usually is the clip or gasket that holds the spray arm on. It wears out. This part is perfect for it supplies a new spray arm, nut and gasket/clip. I think it wears out due to a build up on the arm that puts too much pressure on the clip/gasket. Remember when taking the nut off, if you are standing above the unit with your arm inside, you turn the nut clockwise while looking down. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from Rio Linda, CA
- Parts Used:
- 5304506516, 5304532200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper Spray arm fell off
The Upper Spray Arm is all one piece....so that was nice. You dont have to order all three pieces, like it shows in the diagram. Very easy to order and install parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Massapequa Park, NY
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The part would constantly fall after every dishwasher run
Removed the old spray arm by unscrewing it from the top inside of the dishwasher. Then screwed on the new spray arm. Could not have been any easier and it has not fallen off since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Monroe, GA
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper arm fell off frequently
Unscrewed the mounting nut and the assembly came off . A simple task of taking the new assembly and screwing it back on .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Farrell from NEDERLAND, TX
- Parts Used:
- 5304506516
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Upper Spray arm would fall off during the wash cycle
The spray arm is attached to a part that is screwed on. The new part came completely assembled. I unscrewed the old spray arm and then screwed the new part on. Less than 15 minutes. Works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert & Kathleen from FAIRFAX, VT
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door springs were stretched; with one broken
Followed the on-line tutorial. BINGO!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SUNBURY, PA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Left door spring had stretched and no l held the door upright
Opened the package and inspected the new spring
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul J from LEXINGTON, MA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One door spring was broken - the other was spring.
Instead of moving the unit out from under the counter, I did the job with the unit in place: (1) long reach to remove the old springs and attach the new ones to the frame at back of the unit, (2) use a loop of string to hook onto the other end of the spring, stretch it a little, and keep it stretched by hooking the other end of the loop to the screw that adjusts the unit's height, (3) slip the end of the cable to the front end of the spring and check to make sure that the cable is on its pulley, (4) take the string off the adjusting screw and wiggle it to free it from the end of the spring. (For comfort, lie down on a yoga mat when you do this job - thanks to my wife for this helpful suggestion!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from MURRELLS INLT, SC
- Parts Used:
- 5304506516
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
spray arm on top broke
Just unscrewed the old one and screwed in the new one. Working great! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Libby from NEW HAVEN, CT
- Parts Used:
- 5304506516
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The middle button inside the upper spinner broke
It simply unscrewed and screwed back in in less than 3 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from HADDON TWP, NJ
- Parts Used:
- 5304506516
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
upper spray arm fell off repeatedly
removed clips holding upper rack and pulled out. Simply screwed new sprayer arm in place. Replaced upper rack on track & popped clips in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from WOODBURY, MN
- Parts Used:
- 8581548276014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Was this instruction helpful to you?
Thank you for voting!