FGID2466QF9A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from Lima, OH
- Parts Used:
- 5304507158
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
With the assistance of the CSR, it was great.
Removed and installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Fort Huachuca, AZ
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stem assembly was broken.
I removed the three screws that held the stem assembly in place, removed the old stem assembly and replaced it with the new one. Replaced the screws and began using the dishwasher again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Sacramento, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket leak
First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from Louisville, CO
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Top spray arm was broken
I unscrewed the housing for the spray arm and screwed in the new housing and spray are part. It took less than a minute and works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from PORT ORCHARD, WA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Brass nut split down its side , why ???????
Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theo. J. from Green Bay, WI
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken part that holds bottom spray arm on.
This was great! Removed 3 screws, took out old broken part, set in new part and screwed tight! 1 2 3 and done. Very Fast shipping less than 24 hrs.. WIFE IS HAPPY. Ted W.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from EVERETT, WA
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Heating Element was corroded.
It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LUKE from MARIETTA, GA
- Parts Used:
- 5304532235, 5304507158, 807145201
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
PARTS ORDER TOOK TOO LONG TO ARRIVE
The repair was not the problem. The problem was getting the parts I ordered. When the parts finally shipped I had to wait for them because they just sat in a FedEx shipping warehouse for about a week delaying the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from MARYSVILLE, CA
- Parts Used:
- 5304506516
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Threading problem
Excuse me, as I do not know all the correct nomenclature, but I hope you get what I am saying. The new spray arm would not thread on to my dishwasher water supply coming out of the top of the box. Every time I would try, the supply line would push back up into the housing. Probably need to fix that too, but then I would have to uninstall the DW and just don't have time for that. My old part would thread right on, no problem, but the connection holding it all together was wore out. So I took the new arm and the old "nut" and put them together. They threaded right on, I pulled down on the arm and it is secure. So I had to Frankenstein it a little, but my DW is working, I didn't have to tear it apart and reinstall it, and I didn't have to replace it. Win Win!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from STILWELL, OK
- Parts Used:
- 5304507087
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Wouldn't fix it
The part wasn't correct and I have to pay postage back which is nearly as much as the part so it's stupid for me to spend more money on a part that want work I want order from your store again.
Was this instruction helpful to you?
Thank you for voting!
Plastic had melted on the screw
Eventually broke off old heating element to get it out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from W HEMPSTEAD, NY
- Parts Used:
- 5304507087
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Leaking
Had to shut electricity off and turn water off and disconnect them both. Take the screws out from underneath the counter. Slide out the unit disconnect the filler tube in the back disconnect the hose and replace and repeat the process to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from ROANOKE, VA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part was damaged and dishes weren't clean
Removed 3 screws, swapped parts - done. Wonderful feeling and saved a service call. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phil from lindenhurst, NY
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
spray arm broke
Just unscrew old one and screw in the new one Very Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Bonaire, GA
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper Spray Arm kept falling off.
The new arm came preassembled. I unscrewed the old arm base with my hand and screwed the new arm in place. The whole process took less than a minute. The new part was not made the same way. It was better than the original. Must have been a problem from the manufacturer. WORKS GREAT!!!
Was this instruction helpful to you?
Thank you for voting!