FGID2466QF9A Frigidaire Dishwasher - Instructions

Removed 6 screws from door front panel. Removed two wiring connectors and screws fromdoor latch Replaced and all is great

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.

Replace the latch. Got to cut off old latch, trim wires, install latch, and put on the dishwasher door cover back on with screws

If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

Easy

It only took about 20 minutes to replace. Thanks for the video.

Seriously very easy. Took screws from side of door on inside of washer, silver cover plate came off and was simple to replace the latch using torque screwdriver and phillips screwdriver.

Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps.
installed new hose.

VERY simple---unscrewed three screws on the broken part (the little nubs that held on the bottom spinner were broken off), screwed the new one back in, re-attached the spinner.

I was VERY pleased with the customer service and quick shipping (ordered on Sunday night, the part was delivered Wednesday morning). I would definitely recommend this site to anyone, and would use it again. Five Stars!!!!

Unscrewed the housing for the old piece and screwed on the new part. No tools needed. Easy to use website, fast delivery. Very easy.

My husband and dad actually did the repair, but my husband not being a handy guy said it was, 'so easy, anyone could do it!' He was very nervous about taking on the project, the longest part was testing to make sure it worked(running a cycle).
The simply pulled out the dishwasher, after disconnecting all electrical power, drained the rest of the water that we couldn't see from above, following the video given took out the old part without needing to take out the motor and were able to replace the drain pump, put everything back together besides sliding it into place in case it didn't work, in less than 15 minutes! When the short cycle finished and the water had drained they put it back into place and ran an energy saver cycle and it worked like a charm! Since then(2 weeks ago) we have now ran every function and have had no issues! Every time we open the dishwasher we comment on how much we missed having a dishwasher! Haha!

Latch broke. and it wouldn't run without locking. As a trucker's wife it's up to me to fix whatever breaks or do without. I took apart the door, noticed the model number, and ordered the part. it was easy., it was harder to go thru Thanksgiving and wash dishes by hand.

Removed the cover at the front bottom to gain access to the nuts holding on the element.
Turned off dishwasher breaker.
Removed the wires connected to the element.
With a 1/2" wrench, removed the element mounting screws.
Removed the bottom rack.
Removed the lower spray arm.
Removed the element from 2 clips.
Removed the element.
Put the new element in place.
Clipped it in.
Put new screws on and tightened up with a wrench. Not too much but enough to squash the washers to make a tight seal.
Replaced wires.
Replaced spray arm and bottom rack.
Turned on the breaker.
Ran it through a cycle to check for leaks.
Replaced bottom cover.

Ordered the rack and basket.for 122$ Basket never received . Did not get my money back for a basket. Was planing to return the rack, but easy return will cast me 82$. Keep in
Never buy anything from this company